•If “LPstamp:On” is set, “LP:” is recorded as part of the track name, so the number of characters that can be input in a single MD is reduced. Furthermore, “LP:” is automatically copied if the track name is copied or if the track is divided by using the Divide function.

•MDs recorded in MD LP (LP2 or LP4 Stereo) mode should be played back on a deck that supports MD LP mode. These MDs cannot be played back on other decks.

•Even if you press REC MODE during recording or recording pause, you cannot change the recording mode.

•Even if you press REC MODE repeatedly to select MONO, the monitor signal during recording does not become monaural.

Adjusting the recording level

You can adjust the recording level for both analog and digital recordings.

REC LEVEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Recording

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DISPLAY/CHAR

 

 

 

 

 

 

 

 

1

 

 

Do steps 1 to 6 of “Recording to an MD” on

to

 

 

 

page 14.

 

 

 

MDs

2

 

 

Play the portion of the program source with the

 

 

 

 

 

 

strongest output.

 

3

 

 

Press DISPLAY/CHAR (or DISPLAY) repeatedly

 

 

 

 

until the level of the input signal appears.

 

4

 

 

While monitoring the sound, turn REC LEVEL (or

 

 

 

 

press REC LEVEL/ANALOG OUT LEVEL +/–

 

 

 

 

repeatedly) to raise the recording level to its

 

 

 

 

highest level without turning on the two rightmost

 

 

 

 

indicators on the peak level meters.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Avoid turning on these indicators

5Stop playing the program source.

6To start recording, continue from step 8 of “Recording to an MD” on page 14.

zYou can use the Peak Hold Function

The function freezes the peak level meters at the highest level reached by the input signal.

1While the deck is stopped or playing, press MENU/NO twice. “Setup Menu” appears in the display.

2Turn AMS (or press ./> repeatedly) until “P.Hold Off” (factory setting) appears, then press AMS or YES.

3Turn AMS (or press ./> repeatedly) to select “P.Hold On”, then press AMS or YES.

4Press MENU/NO.

To turn off the Peak Hold Function, select “P.Hold Off” in step 3 above.

zYou can use the remote to turn the Peak Hold Function on or off Z

Press P.HOLD to display “P.Hold On” or “P.Hold Off”.

17 GB

Recording for long times/Adjusting the recording level