To erase a character

Press m/Mrepeatedly until the character to be erased flashes, then press CLEAR.

9Press YES.

The whole name appears in the display, followed by “Complete!!” to indicate that the labeling procedure is completed.

To cancel the operation

Press MENU/NO or x.

Naming a track or an MD using the remote Z

1Press NAME EDIT/SELECT while the deck is in one of the operating modes listed below, depending on what you want to name:

To name

Press while the deck is

5Press YES.

The whole name appears in the display, followed by “Complete!!” to indicate that the labeling procedure is completed.

To cancel the operation

Press MENU/NO or x.

Copying a track or disc name

You can copy an existing track or disc name and use it to name another track on the same disc or the disc itself.

1

While the deck is stopped, playing, or paused,

 

press MENU/NO.

 

“Edit Menu” appears in the display.

2

Turn AMS (or press ./>repeatedly) until

 

“Name ?” appears, then press AMS or YES.

3

 

A track

Playing, paused, recording, or stopped with the track number displayed

Turn AMS (or press ./>repeatedly) until “Nm

Copy ?” appears, then press AMS or YES.

The MD

Stopped with total number of tracks displayed

4 Turn AMS (or press ./>repeatedly) until the

track number (when copying the track name) or

MDs Recorded Editing

A flashing cursor appears in the display.

2Press NAME EDIT/SELECT repeatedly to select the character type.

To select

Press repeatedly until

 

 

Uppercase letters

“Selected AB(C)” appears in the

and symbols1)

display

Lowercase letters

“Selected ab(c)” appears in the display

and symbols1)

 

Numbers

“Selected 12(3)” appears in the display

 

 

1) Only ’ – / , . ( ) : ! ? can be selected.

3Enter a character using letter/number buttons.

If you have selected uppercase or lowercase letters

1Press the corresponding letter/number button repeatedly until the character to be entered flashes. Or, press the button once and press ./> repeatedly.

To select symbols, press .repeatedly while “A” is flashing.

2Press M.

The flashing character is entered and lights continuously and the cursor shifts to the right.

If you have selected numbers

Press the corresponding number button.

The number is entered and the cursor shifts to the right.

4 Repeat steps 2 and 3 to enter the rest of the name.

“Disc” (when copying the disc name) flashes, then

press AMS or YES to copy the selected name.

When “No Name” appears in the display

The selected track or disc has no name.

5 Turn AMS (or press ./>repeatedly) until the

track number (when naming a track) or “Disc”

(when naming a disc) flashes, then press AMS or

YES to enter the copied name.

“Complete!!” appears for a few seconds and the name

is copied.

To cancel the operation

Press MENU/NO or x.

zWhen “Overwrite ?(?)” appears in step 5 above

The track or the disc selected in step 5 already has a name. If you wish to replace the name, press AMS or YES again while the indication appears in the display.

If the track has been recorded in MD LP mode with the “LPstamp On” setting (page 15), “Overwrite ?(?)” also appears even if a track name is not assigned. In this case if you copy the track name, the “LP:” indication disappears from the track name.

Renaming a track or MD Z

1Press NAME EDIT/SELECT while the deck is in one of the operating modes listed below, depending on what you want to rename:

To rename

Press while the deck is

To change a character

Press m/Mrepeatedly until the character to be

A track

Playing, paused, recording, or stopped with the track number displayed

changed flashes, press CLEAR to erase the character,

then repeat steps 2 and 3.

The MD

Stopped with total number of tracks displayed

A track or disc name appears in the display.

36 Naming a track or MD