Sony Model HTP-36DW 11

Name		Function
R Control		After pressing AMP MENU
	buttons	(D), DVD MENU (J), or
		MENU (N), press the control
		button V, v, B or b to select
		the settings. When you press
		DVD MENU or MENU, press
		the control button to enter the
		selection.

S DISPLAY		Press to select the information
		displayed on the TV screen of
		the VCR, satellite tuner, CD
		player or DVD player.

T -/--		Press -/-- and TV (P) at the
		same time to select the
		channel entry mode, either
		one or two digits of the TV.

	>10/x	Press to select
		– track numbers over 10 of the
		VCR, satellite tuner or CD
		player.
		– channel numbers of the
		Digital CATV terminal.

	CLEAR	Press to
		– clear a mistake when you
		press the incorrect numeric
		buttons.
		– return to continuous
		playback, etc. of the satellite
		tuner or DVD player.

U Numeric		Press to
	buttons	– preset/tune to preset
	(number 5*)	stations.
		– select track numbers of the
		CD player or DVD player.
		Press 0/10 to select track
		number 10.
		– select channel numbers of
		the VCR or satellite tuner.
		Press the numeric buttons and
		TV (P) at the same time to
		select the TV channels.

V 2CH		Press to select 2CH STEREO
		mode.

WA.F.D. Press to select A.F.D. mode.

XAUTO CAL Press to activate the Auto Calibration function.

Name Function

YTV/VIDEO Press TV/VIDEO and TV

(P) at the same time to select the input signal (TV input or video input).

SLEEP	Press to activate the Sleep
	Timer function and the
	duration which the receiver
	turns off automatically.

*The number 5, MASTER VOL +, TV VOL +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.

Notes

•Some functions explained in this section may not work depending on the model.

•The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

Started Getting

11GB

Contents

Page WARNING For customers in Europe About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Front panel Page About the indicators on the display Page Rear panel Remote commander Page Page 1: Installing speakers Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws To connect the speaker correctly 3a: Connecting the audio components How to hook up your components Audio input jack to be connected DigitalAnalog High quality sound Connecting audio components Component to be connected Hooking up a TV monitor 1Connecting audio 2Connecting video If you connect a DVD recorder Hooking up a satellite tuner Hooking up a VCR 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6: Calibrating the automatically appropriate settings (AUTO CALIBRATION) Before you perform Auto Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7:Adjusting the speaker levels and balance To turn off the test tone To mute the sound To avoid damaging your speakers To listen to the sub woofer Listening/Watching a component Listening to a Super Audio CD/CD Turn on the Super Audio CD player/CD player, then place the disc on the tray Turn on the receiver Press SA-CD/CD Watching a DVD Turn on the TV and DVD player Press DVD Switch the input of the TV so that an image of the DVD is displayed Set up the DVD player To return to the previous display To exit the menu Overview of the menus Page LEVEL menu parameters TONE menu parameters SUR menu parameters TUNER menu parameters AUDIO menu parameters SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR POS. (Surround speaker position) Calibrating the appropriate settings automatically Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Presetting radio stations 3 Press MEMORY 4 Press the numeric button to select the preset station 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Using the Radio Data System (RDS) Audio input modes All inputs except the FM and AM band FM and AM band Changing button assignments Categories and the corresponding buttons To clear all remote button assignments On safety On power sources On heat buildup On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index Numerics