Manuals / Brands / TV and Video / DVD Player / Sony / TV and Video / DVD Player

Sony Model HTP-36DW Component to be connected, 3b: Connecting the video components, How to hook up your components, Video input/output jack to be connected

1 64

Download 64 pages, 2.28 Mb

3b: Connecting the video components

How to hook up your components

This section describes how to hook up your components to this receiver. Before you begin, refer to “Component to be connected” below for the pages which describe how to connect each component.

After hooking up all your components, proceed to “4: Connecting the antennas” (page 23).

Video input/output jack to be connected

The image quality depends on the connecting jack. Refer to the illustration that follows. Select the connection according to the jacks on your components.

TV monitor, etc.

INPUT jack COMPONENT

VIDEOVIDEO

Started Getting

	Component to be connected
	Component	See	Receiver MONITOR	COMPONENT
	Component	See	OUT jack	COMPONENT	VIDEO
			OUT jack	VIDEO
	TV monitor	page 18		VIDEO
	TV monitor	page 18
	DVD player/DVD recorder	page 19
	Satellite tuner	page 21
	VCR	page 22
				COMPONENT	VIDEO
				VIDEO	VIDEO

Receiver INPUT jack

Video component

OUTPUT jack COMPONENT

VIDEOVIDEO

High quality image

Notes

•Connect image display components such as a TV monitor or a projector to the MONITOR OUT jack on the receiver.

•Turn on the receiver when the video and audio of a playback component are being output to a TV through the receiver. If the power supply of the receiver is not on, neither video nor audio is transmitted.

17GB

Contents

Page WARNING For customers in Europe About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Front panel Page About the indicators on the display Page Rear panel Remote commander Page Page 1: Installing speakers Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws To connect the speaker correctly 3a: Connecting the audio components How to hook up your components Audio input jack to be connected DigitalAnalog High quality sound Connecting audio components Component to be connected Hooking up a TV monitor 1Connecting audio 2Connecting video If you connect a DVD recorder Hooking up a satellite tuner Hooking up a VCR 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6: Calibrating the automatically appropriate settings (AUTO CALIBRATION) Before you perform Auto Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7:Adjusting the speaker levels and balance To turn off the test tone To mute the sound To avoid damaging your speakers To listen to the sub woofer Listening/Watching a component Listening to a Super Audio CD/CD Turn on the Super Audio CD player/CD player, then place the disc on the tray Turn on the receiver Press SA-CD/CD Watching a DVD Turn on the TV and DVD player Press DVD Switch the input of the TV so that an image of the DVD is displayed Set up the DVD player To return to the previous display To exit the menu Overview of the menus Page LEVEL menu parameters TONE menu parameters SUR menu parameters TUNER menu parameters AUDIO menu parameters SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR POS. (Surround speaker position) Calibrating the appropriate settings automatically Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Presetting radio stations 3 Press MEMORY 4 Press the numeric button to select the preset station 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Using the Radio Data System (RDS) Audio input modes All inputs except the FM and AM band FM and AM band Changing button assignments Categories and the corresponding buttons To clear all remote button assignments On safety On power sources On heat buildup On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index Numerics