Manuals / Brands / TV and Video / DVD Player / Sony / TV and Video / DVD Player

Sony Model HTP-36DW Resetting sound fields to the initial settings, 1,22, Using only the front speakers and sub woofer, Press 2CH, (2CH STEREO), While holding down 2CH, press

1 64

Download 64 pages, 2.28 Mb

Using only the front speakers and sub woofer(2CH STEREO)

In this mode, the receiver outputs the sound from the front left/right speakers and sub woofer.

When multi channel surround formats are input, the signals are downmixed to 2 channel with bass frequencies being output from the sub woofer.

When standard 2 channel stereo sources are input, the receiver’s bass redirection circuitry will be activated. The front channel bass frequencies will be output from the sub woofer.

TUNER AMP MENU

2CH

A.F.D.

MOVIE MUSIC

2CH

DUAL MONO

1 2 3

Press 2CH.

Resetting sound fields to the initial settings

Be sure to use the buttons on the receiver for this operation.

1,22

		DISPLAY DIMMER				2CH	A.F.D.	MOVIE	MUSIC
?/1
					AMP MENU ENTER				MASTER
									VOLUME
AUTO CAL MIC	MEMORY	PRESET TUNING	+
			VIDEO 1 VIDEO 2 DVD SA-CD/CD	FM	AM
	FM MODE	TUNING	+
PHONES						INPUT MODE

1 Press ?/1 to turn off the receiver.

2 While holding down 2CH, press ?/1.

“S.F. CLR.” appears on the display and all sound fields are reset to their initial setting.

Sound Surround Enjoying

45GB

Contents

Page WARNING For customers in Europe About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Front panel Page About the indicators on the display Page Rear panel Remote commander Page Page 1: Installing speakers Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws To connect the speaker correctly 3a: Connecting the audio components How to hook up your components Audio input jack to be connected DigitalAnalog High quality sound Connecting audio components Component to be connected Hooking up a TV monitor 1Connecting audio 2Connecting video If you connect a DVD recorder Hooking up a satellite tuner Hooking up a VCR 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6: Calibrating the automatically appropriate settings (AUTO CALIBRATION) Before you perform Auto Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7:Adjusting the speaker levels and balance To turn off the test tone To mute the sound To avoid damaging your speakers To listen to the sub woofer Listening/Watching a component Listening to a Super Audio CD/CD Turn on the Super Audio CD player/CD player, then place the disc on the tray Turn on the receiver Press SA-CD/CD Watching a DVD Turn on the TV and DVD player Press DVD Switch the input of the TV so that an image of the DVD is displayed Set up the DVD player To return to the previous display To exit the menu Overview of the menus Page LEVEL menu parameters TONE menu parameters SUR menu parameters TUNER menu parameters AUDIO menu parameters SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR POS. (Surround speaker position) Calibrating the appropriate settings automatically Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Presetting radio stations 3 Press MEMORY 4 Press the numeric button to select the preset station 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Using the Radio Data System (RDS) Audio input modes All inputs except the FM and AM band FM and AM band Changing button assignments Categories and the corresponding buttons To clear all remote button assignments On safety On power sources On heat buildup On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index Numerics