Sony Model HTP-36DW Specifications

Specifications

Amplifier section

Power Output1)

Models of area code CEL, CEK (6 ohms 1 kHz, THD 0.7%)

FRONT2):	85 W/ch
CENTER2):	85 W
SUR2):	85 W/ch
(6 ohms 1 kHz, THD 10%)
FRONT2):	122 W/ch
CENTER2):	122 W
SUR2):	122 W/ch
1)Measured under the following conditions:
Area code	Power requirements

CEL, CEK	230 V AC, 50 Hz

2)Depending on the sound field settings and the source, there may be no sound output.

Inputs (Analog)

SA-CD/CD,	Sensitivity: 800 mV
VIDEO 1, 2, DVD	Impedance: 50 kohms

Inputs (Digital)

DVD (Coaxial)	Sensitivity: –
	Impedance: 75 ohms

VIDEO 1, 2	Sensitivity: –
(Optical)	Impedance: –

Outputs (Analog)

SUB WOOFER	Voltage: 2 V
	Impedance: 1 kohm

Reproduction frequency range:
	28 – 20,000 Hz
Tone

Gain levels	±6 dB, 1 dB step

FM tuner section
Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced

Intermediate Frequency

10.7 MHz

AM tuner section

Tuning range

Models of area code CEL, CEK With 9-kHz tuning scale:

531 - 1,602 kHz

AntennaLoop antenna Intermediate Frequency

450 kHz

Video section

Inputs/Outputs

Video:1 Vp-p, 75 ohms

COMPONENT VIDEO:

Y: 1 Vp-p, 75 ohms

PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms

80 MHz HD Pass Through

General

Power requirements

	Area code	Power requirements
	CEL, CEK	230 V AC, 50/60 Hz

	Power consumption

	Area code	Power consumption

	CEL, CEK	190 W
	Power consumption (during standby mode)
	Power consumption (during standby mode)			Additional
		0.2 W		Additional
		0.2 W
	Dimensions (w/h/d) (Approx.)
		430 × 145 × 300 mm
		including projecting parts		Information
		and controls		Information
		and controls
	Mass (Approx.)	7.5 kg

continued

61GB

Contents

Page WARNING For customers in Europe About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Front panel Page About the indicators on the display Page Rear panel Remote commander Page Page 1: Installing speakers Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws To connect the speaker correctly 3a: Connecting the audio components How to hook up your components Audio input jack to be connected DigitalAnalog High quality sound Connecting audio components Component to be connected Hooking up a TV monitor 1Connecting audio 2Connecting video If you connect a DVD recorder Hooking up a satellite tuner Hooking up a VCR 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6: Calibrating the automatically appropriate settings (AUTO CALIBRATION) Before you perform Auto Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7:Adjusting the speaker levels and balance To turn off the test tone To mute the sound To avoid damaging your speakers To listen to the sub woofer Listening/Watching a component Listening to a Super Audio CD/CD Turn on the Super Audio CD player/CD player, then place the disc on the tray Turn on the receiver Press SA-CD/CD Watching a DVD Turn on the TV and DVD player Press DVD Switch the input of the TV so that an image of the DVD is displayed Set up the DVD player To return to the previous display To exit the menu Overview of the menus Page LEVEL menu parameters TONE menu parameters SUR menu parameters TUNER menu parameters AUDIO menu parameters SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR POS. (Surround speaker position) Calibrating the appropriate settings automatically Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Presetting radio stations 3 Press MEMORY 4 Press the numeric button to select the preset station 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Using the Radio Data System (RDS) Audio input modes All inputs except the FM and AM band FM and AM band Changing button assignments Categories and the corresponding buttons To clear all remote button assignments On safety On power sources On heat buildup On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index Numerics