To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1 Press (TALK) and wait until the TALK/BATT LOW lamp lights up. The dialing keys light up
2 Press (SPEEDÊDIAL).
3 Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
Resetting the digital security code
The first time you charge the battery pack, a random security code is automatically assigned between the base unit and the handset. Only a handset which has this security code can make calls through the base unit. This system prevents the possibility of other cordless telephone handsets making calls through your base unit. You normally do not need to reset the security code. However, in the unlikely event that you suspect that another cordless phone uses the same security code, you can manually change the code. Pick up the handset from the base unit, and proceed as follows:
Mounting your phone on the wall
1
2
3 Attach the telephone line cord and AC power adaptor cord to the base unit.
Use the shorter cord for mounting.
4 Plug the telephone line cord into the telephone outlet, and hook the base unit to the wall plate as illustrated. Then fully extend the antenna.
1, 2 | 3 | 4 |
Wall plate
TALK/BATT
LOW Lamp
Note
1
2
3
4
5
Press (PGM).
The TALK/BATT LOW lamp flashes.
Press (#).
You hear a confirmation beep.
The dialing keys light up
Press three of the dialing keys (001 to 999) to store a new code.
Press (PGM).
You hear a long confirmation beep and the TALK/BATT LOW lamp goes off.
Immediately replace the handset on the base unit
You hear a long confirmation beep and the phone stores the new code.
Troubleshooting
Problem | Solution |
The handset does not make or | • Reset the digital security code. |
receive a call. | • Place the base unit away from noise sources |
| such as TV, FM radio or PC. |
| • Make sure the base unit is connected to an AC |
| outlet. |
| • The battery pack may be discharged. Charge |
| the battery pack for about 12 hours. |
|
|
You hear no dial tone. | • Make sure the telephone line cord is securely |
| connected to the telephone outlet. |
The handset doesn’t connect at • Make sure the dial mode setting (pulse or tone)
all, even the numbers you dial | is correct. |
are correct. |
|
|
|
The handset does not redial | • Make sure the number (including the tone and |
correctly. | pause digits, if used) you last dialed is less |
| than 32 digits. |
The handset does not make a • Make sure there is a phone number correctly
speed dialing call. | stored in the speed dialing. |
| • Store the desired phone number once more. |
The handset does not ring. | • Make sure the base unit is connected to an AC |
If the battery pack in the handset is completely discharged, or is removed from the handset for more than several seconds, the digital security code stored will be lost. If this happens, charge the battery pack and a new security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset. The code can be changed as often as desired.
Paging
You can page the handset from the base unit. Note that you can’t page if the handset is in use.
To page
Press (PAGE).
The handset rings.
When you keep pressing (PAGE), the handset rings continuously.
Maintenance
•Clean the cabinets with a soft cloth slightly moistened with water or a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine as they may damage the finish of the cabinet.
•If the charge terminals of the base unit and handset are soiled, wipe them with a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult your nearest Sony dealer.
| outlet. |
|
The handset does not ring | • The battery may have little or no power. |
|
when paging from the base | Charge the battery for more than 12 hours. |
|
unit. | • Extend the antenna of the base unit vertically. |
|
| • Place the base unit away from noise sources. |
|
|
|
|
You hear a beep every 3 | • Charge the battery pack for about 12 hours. |
|
seconds and the TALK/BATT |
|
|
LOW lamp flashes. |
|
|
|
|
|
|
|
|
Specification
General |
|
Frequency control | |
Operation mode | FM, duplex |
Operation channel | 25 channels |
Supplied accessories | AC power adaptor |
| Telephone line cords (2) |
| Rechargeable battery pack |
| Directories (2 sheets) |
Handset |
|
Power source | Rechargeable battery pack |
Battery life | Standby: Approx. 14 days |
| Talk: Approx. 6 hours |
Dimensions | Approx. 2 3⁄8 x 8 x 2 3⁄8 inches (w/h/d), antenna |
| excluded (Approx. 59 x 201 x 59 mm) |
| Antenna: 4 3⁄8 inches (110 mm) |
Mass | Approx. 6.2 oz (Approx. 175 g), battery included |
Base unit |
|
Power source | DC 9V from AC power adaptor |
Battery charging time | Approx. 12 hours |
Dimensions | Approx. 5 7⁄8 x 2 3⁄8 x 9 inches (w/h/d), antenna |
| excluded |
| (Approx. 148 x 58 x 226 mm) |
| Antenna: 17 inches (430 mm) |
Mass | Approx. 9.5 oz (Approx. 270 g) |
Design and specifications are subject to change without notice.
SPP Q110/Q120 3 856 344 11 E U