Location and function of parts

Front panel

1

3

8

6

7

9

0 qa

 

 

 

 

 

 

 

 

 

 

 

 

OUTPUT

 

 

 

 

 

 

 

 

MIC1/WL1

MIC2/WL2

MIC3

MIC4

MIC5/LINE1

MIC6/LINE2

LINE3

LINE4

VU

1

2

3

4

5

6

7

8

VU

MASTER A

 

MASTER B

 

+3

 

 

 

 

 

 

 

 

+3

 

 

SIGNAL

SIGNAL

SIGNAL

SIGNAL

SIGNAL

SIGNAL

SIGNAL

SIGNAL

0

 

 

 

 

 

 

 

 

0

OVER GAIN

PROTECTION

OVER GAIN

 

OVER GAIN

OVER GAIN

OVER GAIN

OVER GAIN

OVER GAIN

OVER GAIN

OVER GAIN

OVER GAIN

-5

 

 

 

 

 

 

 

 

-5

-

CLIP

-

SCENE

-10

 

 

 

 

 

 

 

 

-10

-

-

-

-

-

-

-

-

-20

 

 

 

 

 

 

 

 

-20

 

 

 

RECALL

POWER

 

 

 

 

 

 

 

LINE 4 SELECT

 

 

 

 

 

A

MASTER

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

ON OFF

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCK

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

B

RS-232C

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WL 1

MIC TUNER

WL 2

 

qs 2

1POWER button and POWER indicator

Pressing the POWER button turns on the power. The POWER indicator lights in green when the power turns on.

You can switch the projectors and displays connected to the SRP-X700P, to power-on state or to power standby state from the SRP-X700P as they are interlocked by the SRP-X700P Manager setup.

By default when shipped from the factory, the projectors and displays powers are interlocked with the POWER button of the SRP-X700P.

Turning on the POWER button of the SRP-X700P, sets the AV equipment connected to the CONTROL S OUT terminals 1 through 4, to power-on state. Note that the AV equipment does not enter the power standby state when the POWER button of the SRP-X700P is turned off.

2Input faders

•MIC1/WL1 and MIC2/WL2 faders

Adjusts the level of the signals supplied from the MIC1/ WL1 and MIC2/WL2 input terminals.

Either a wireless microphone or wired microphone can be connected. When the wireless tuner receives the signal, the wireless microphone is selected automatically.

•MIC3 and MIC4 faders

Adjusts the level of the signals supplied from the MIC3 and MIC4 input connectors.

•MIC5/LINE1 and MIC6/LINE2 faders

Adjusts the level of the signals supplied from the MIC5/ LINE1 and MIC6/LINE2 input terminals. The MIC/LINE selector button on the rear panel can be used to switch the reference input level.

By default, LINE is selected.

•LINE3 and LINE4 faders

Adjusts the level of the signals supplied from the LINE3 and LINE4 input terminals.

These input faders are not the “moving” type.

5 4 qd

3Input indicators

•SIGNAL indicator

The SIGNAL indicator lights in green when a signal is input to each input terminal.

•OVER GAIN indicator

The OVER GAIN indicator lights in red when the input level exceeds the GAIN LIMIT value that is set up by the SRP-X700P Manager.

By default, the GAIN LIMIT is set to 10 dB.

•–∞indicator

The –∞indicator lights in yellow when no audio is output in

such cases as muting or when the INPUT fader is located at the –∞level position.

4Tuner slots (WL 1/2)

This slot accepts the 800 MHz band wireless tuner unit WRU- 806B (option). It accepts up to two units. (For installation, refer to page 8.) The WRU-806B Operating Instructions provide full details on operating the tuner unit.

For operation of the tuner unit, read the WRU-806B Operating Instructions thoroughly.

5LINE 4 SELECT button

You can select a device to be connected to the input connectors from 4A to 4F of LINE 4.

6Master volume

With the master volume, you can control multiple faders that are set as a single group. The faders to be controlled by the master volume are set by the SRP-X700P Manager.

By default, the MASTER A is set to MIC1 to MIC4 input faders, and the MASTER B is set to LINE1 to LINE4 input faders.

The master volume is not the “moving” type.

•OVER GAIN indicator

The OVER GAIN indicator lights in red when the input level exceeds the GAIN LIMIT value that is set by the SRP- X700P Manager.

By default, the GAIN LIMIT is set to 10 dB.

•–∞indicator

The –∞indicator lights in yellow when no audio is output in

such cases as muting or when the INPUT fader is located at the –∞level position.

4