Manuals / Brands / Home Audio / Stereo Receiver / Sony / Home Audio / Stereo Receiver

Sony STR-DG500 Error codes, To rectify the error, Error code and remedies, Error and warning codes

1 76

Download 76 pages, 2.59 Mb

The table below shows the display when measurement starts.

Measurement for	Display
Environment noise level	NOISE.CHK

Speaker connection	MEASURE and SP
	DET. appears
	alternately*

Speaker level	MEASURE and
	GAIN appears
	alternately*

Speaker distance	MEASURE and
	DISTANCE appears
	alternately*

*The corresponding speaker indicator lights up in the display during measurement.

When measurement ends, “COMPLETE” appears on the display and the settings are registered.

Notes

•Auto Calibration cannot detect the sub woofer. Therefore, all sub woofer settings will be maintained.

•You cannot select Auto Calibration when headphone is connected.

•The measurement process will take a few minutes to complete.

Tips

•When Auto Calibration starts:

–Stand some distance from the speakers and the listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement.

–Avoid making noise to get a more accurate measurement.

•The Auto Calibration function will be canceled when you do the following during the measurement process:

–Press ?/1, input buttons or MUTING.

–Change the volume level.

–Press AUTO CAL again.

Error and warning codes

Error codes

When an error is detected during Auto Calibration, an error code will appear on the display cyclically after each measurement process as follows:

Error code t blank display t (error code t blank display)a) t PUSH t blank display

tENTER

a)Appears when there are more than one error code.

To rectify the error

1Record down the error code.

2Press the control button.

3Press ?/1 to turn off the receiver.

4Rectify the error.

For details, see “Error code and remedies” below.

5Turn on the receiver and perform Auto Calibration again (page 27).

Error code and remedies

Error	Explanation	Remedies
code

ERROR 10	The environment	Make sure the
	is too noisy.	environment is
		quiet during Auto
		Calibration.

ERROR 11 The speakers are		Place your speakers
	placed too near	further away from
	the optimizer	the optimizer
	microphone.	microphone.

ERROR 20	Front speakers	Check the front
	are not detected	speaker
	or only one front	connection.
	speaker is
	detected.

ERROR 21	Only one	Check the surround
	surround speaker	speaker
	is detected.	connection.

ERROR 23	Surround back	Be sure to connect
	speaker is	the surround
	detected but	speakers.
	surround

speakers are not connected.

28GB

Contents

Page WARNING For customers in the United States CAUTION Note to CATV system installer: For customers in Europe About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Description and location of parts Front panel Page About the indicators on the display Page Rear panel Remote commander Page Page Example of a 6.1 channel speaker system configuration Example of a 5.1 channel speaker system configuration 2: Connecting speakers Component to be connected Connecting components with multi channel output jacks Connecting components with analog audio jacks Reassigning video input signals to another input Hooking up a TV monitor 1Connecting audio 2Connecting video If you connect a DVD recorder Hooking up a satellite tuner Hooking up components with analog video and audio jack 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6:Selecting the speaker system 7:Calibrating the appropriate settings automatically Error codes To rectify the error Error code and remedies Warning codes To change the settings manually Warning code and solution 8:Adjusting the speaker levels and balance To mute the sound To avoid damaging your speakers Listening/Watching a component Listening to a Super Audio CD/CD Turn on the Super Audio CD player/CD player, then place the disc on the tray Turn on the receiver Press SA-CD/CD Watching a DVD 1 Turn on the TV and DVD player 2 Turn on the receiver 3 Press DVD 5 Set up the DVD player To return to the previous display To exit the menu Overview of the menus Page Page LEVEL menu parameters TONE menu parameters SUR menu parameters Types of the surround back decoding functions TUNER menu parameters AUDIO menu parameters VIDEO menu parameters SYSTEM menu parameters xSUR SPK (Surround speakers) xSB SPK (Surround back speaker) xFRT DIST. (Front speaker distance) xCNT DIST. (Center speaker distance) xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSB DIST. (Surround back speaker distance) xSUR POS (Surround speaker position) xCRS. FREQ (Speaker crossover frequency) xDIMMER (Brightness of the display) Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode If you connect a sub woofer Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Listening to the sound without any adjustment Resetting sound fields to the initial settings 1 Press ?/1 to turn off the power While holding down 2CH, press Listening to FM/AM radio Using the controls on the receiver In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically 2 Hold down MEMORY/ENTER and press ?/1 to turn the receiver back on Presetting radio stations Presetting radio stations 3,5 3 Press MEMORY 4 Press the numeric buttons to select a preset number 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Using the Radio Data System (RDS) Receiving RDS broadcasts Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly on the receiver Description of program types Audio input modes Watching component images from other inputs Assignable inputs for component video input All inputs except the FM and AM band FM and AM band Using the Sleep Timer Press SLEEP repeatedly while the power is on Recording using the receiver Recording onto a MiniDisc or audio tape 1 Press one of the input buttons to select the playback component Changing button assignments Categories and the corresponding buttons To clear all remote button assignments xDolby Pro Logic xDolby Surround (Dolby Pro Logic) xDTS 96/24 xDTS Neo:6 xDTS Digital Surround On safety On power sources On heat buildup On placement On operation Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory AUDIO POWER SPECIFICATIONS Page Page Index Numerics