Getting Started

VCR

Receiver

VCR

VIDEO

OUTPUT

INPUT

VIDEO OUT VIDEO IN

VIDEO

VIDEO

AUDIO OUT AUDIO IN

AUDIO AUDIO

L

L

R

R

Use the function buttons (TV/LD, CD, MD/TAPE etc) to select the VIDEO AUDIO OUT signal. You can record this audio signal by connecting a recording component such as a cassette deck (to the VIDEO AUDIO OUT jack).

DVD player/AC-3 decoder

What cables will I need?

•Audio cable (not supplied) (1 for each 5.1 CH/DVD FRONT and REAR jacks)

White (L)

White (L)

Red (R)

Red (R)

•Monaural audio cable (not supplied) (1 for each 5.1 CH/DVD CENTER and WOOFER jacks)

Black Black

•Video cable (not supplied) (1 for the 5.1 CH/DVD VIDEO IN jack)

Yellow Yellow

You can play decoded Dolby Digital AC-3 soundtracks

through the speakers connected to the amplifier.

If you have a Dolby Digital AC-3 decoder you can amplify a decoded Dolby Digital AC-3 soundtrack with the following connections.

Receiver

 

Dolby Digital AC-3

 

decoder, etc.

5.1 CH/DVD

 

 

PRE OUT

 

 

 

FRONT REAR CENTER VIDEO

 

CENTER

REAR FRONT

L

 

 

 

 

VIDEO

WOOFER

 

 

 

 

R

 

 

 

WOOFER

 

 

 

Speaker System Hookups

Overview

This section describes how to connect your speakers to the receiver. Although front (left and right) speakers are required, centre and rear speakers are optional. Adding centre and rear speakers will enhance the surround effects. Connecting an active woofer will increase bass response. For specific locations of the terminals, see the illustration below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPEAKERS

 

 

 

SPEAKERS REAR

 

 

FRONT A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WOOFER

SPEAKERS

SPEAKERS

 

CENTER

FRONT B

For optimum surround sound effect, place your speakers as shown below.

Rear speaker

60 - 90 cm

45°

What cords will I need?

Speaker cord (not supplied) (1 for each speaker)

(+)

(+)

(–)

(–)

Twist the stripped ends of the cord about 15 mm (2/3 inch). Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass.

Where do I go next?

Go on to the next section to connect the speakers.

(continued)

7GB