Sound Performance Lab Model 2601 manual Mic Level Output, Line Output, Pre Simulator Out

Rear Panel

065165-&7&-*$ .
°       (/%  
0VUQVUPVUQVU
$POOFDUQSFBNQMJGJFS
FWFM0VUQVU	-JD .#BM

#BM
.JD
-FWFM
0VUQVU

$POOFDU
UP
NJD
QSFBNQMJGJFS

0VUQVU
(BJO
EPFT
OPU
BGGFDU
UIJT
PVUQVU



(/%







°

.*$
-&7&-
065165

*/&

- ° 





(/%




FWFM

-JOF
-#BM

Connections

Mic Level Output

The microphone level output is usable just like any mike out. The Miking Level control on the Transducer front panel regulates the signal. The Output Gain control has no influence on the Miking Level output. Just as with conventional cabinet miking, variations in microphone preamp choices may of course be made to influence further the sonic result.

Balanced XLR output, wiring: pin 1 = ground, pin 2 = hot (+), pin 3 = cold (-).

Line Output 1

The front panel Output Gain control regulates the output signal, which appears at the Line Output 1 connector.

Balanced XLR output, line signal with +4dB.

Wiring: pin 1=ground, pin 2=hot (+), pin 3=cold (-).

		#BM -JOF -FWFM 0VUQVU
		  (/%        °
		-*/& 065165 
		*/&	-
(/%4MFFWF	°   JOH  3  JQ  5+BDL
°     3   (/%    -9			/PSNBM
FWFM0VUQVUT		-JOF -#BMBODFE	3FWFSTF
			 1IBTF

#BMBODFE -JOF -FWFM 0VUQVUT	 1IBTF
		3FWFSTF
9-3   (/%        °		/PSNBM

+BDL
5JQ

 3JOH

° 4MFFWF


(/%

-*/&
065165


Line Output 2

The front panel Output Gain control regulates the output signal, which appears at the Line Output 2 connectors.

Balanced XLR and 1/4” TRS connector, line signal with +4dB.

Wiring XLR: pin 1 = ground, pin 2 = hot (+), pin 3 = cold (-).

Wiring TRS: tip =hot (+), ring = cold (-), sleeve = ground.

The Line Output 2 phase switch provides for a reversal of this output‘s signal phase.

IMPORTANT ADVICE

Use only one (either an XLR or 1/4" TRS) Line Output 2 connection at a time. Using both output connections simultaneously can impair the signal through impedance mismatches from the doubled load that can lead to such problems as high frequency damping.

However, Line Output 1 and 2 can be used simultaneously.

"503065		-6.13&4*
(/%4MFFWF			  JQ 5
BNQMJGJFSFGGFDUT
$POOFDUBEEJUJPOBM
FWFM0VU	-JOF -6OCBM

6OCBM
-JOF
-FWFM
0VU

$POOFDU
UP
BEEJUJPOBM

BNQMJGJFS
PS
FGGFDUT

5JQ

 4MFFWF


(/%

13&
4*.6-"503
065

Pre Simulator Out

This output is independent from Speaker Simulation and thus independent from Transducer adjustments. The signal at this Pre Simulator Out is that of the power-reduced amp signal (line level). With this arrangement you can feed a separate amp and guitar box setup or effects machines.

Connector variant and connections correspond to industry standards: Unbalanced 1/4" Jack connector with the signal at tip and ground at sleeve.

Mic Level Output, Line Output 1, Line Output 2 (XLR or TRS connection) und Pre Simulator Out may all be used simultaneously.

12 Transducer