HTINT650S, HTINT650W
◐NOTES
1.You can install the camera indoors or outdoors.
2.Be careful not to scratch the lens or dome cover.
3.Use 1Amp power supply at 12V DC or 24V AC.
◐FEATURES
1.IP67 (Waterproof)
2.Construction
Body : Aluminum, Dome : Polycarbonate
3.(Optional) Wall, Ceiling and pole mounts available
4.25M range visible in total darkness with 24pcs of IR LEDs (depends upon scene reflection)
5.Side control board for easy function adjustment
6.Dual power (12V DC or 24V AC) operation
◐DIMENSION
◐HOW TO INSTALL
1. Camera installation
(1)Fix the camera with the supplied screws on ceiling or wall mount.
(2)Please refer to '3. Camera angle adjustment' regarding adjust camera angle.
(3)Lens adjustment
After opening the LED cover,
①By turning the
②By turning the
(4) Reassemble the camera.
<Ceiling mount>
<Wall mount>
2. Pipe application
(1)Remove the screw for fixing a cable on the bottom of the base.
(2)Open the DOME COVER.
(3)Remove the TAP COVER and place the cables there.
(4)After distributing cables, use the TEPLON tape to wipe the pipe.
(5)Attach the pipe to the base.
<Caution> If you don't wipe TEFLON tape on pipe, it might cause water intrusion issues.
3. Camera angle adjustment
(1)Pan adjustment : Grasp the disk of camera and adjust direction to the right or
(2)Tilt adjustment : Grasp the LED cover of camera and adjust direction to up or down(6˚~ 90˚)
(3)Roll adjustment : Grasp the camera holder and then
<Caution> If you try to adjust the camera out of limited angle, it might cause damage to camera.
◐SPECIFICATION
| Model No. |
| HTINT650S, HTINT650W |
| Image Sensor |
| 1/3" SONY SUPER HAD CCDⅡ |
| Effective Pixel |
| 768(H) X 494(V) PIXEL |
Cell Size |
| 6.35㎛(H) X 7.4㎛(V) | |
| Scanning System |
| 2 : 1 Interlace |
| Sync. Type |
| Internal / Line lock(24V AC) |
OSD |
| ||
| WDR Set |
| SSDR / BLC / HLC / OFF |
| Resolution |
| Color : 600 |
S/N Ratio |
| 52dB(AGC OFF, Weight ON) | |
|
|
| LED ON : 0 Lux(25M Range) |
Min. Illumination |
| LED OFF : 0.0005 Lux(Color | |
|
|
| 0.0002 Lux(B/W |
| Color Temp. |
| ATW(1,700°K ~ 11,000°K) / |
|
| AWC / MANUAL / OUTDOOR / INDOOR | |
|
|
| |
| Shutter |
| 1/60 ~ 1/120,000sec |
| Intensifier |
| AUTO / FIXED / OFF(x2 ~ x512 selectable) |
Gain Control |
| LOW / HIGH / OFF | |
| Speco DNR |
| OFF / ON(1 ~ 32 Level adjustable) |
V | Motion |
| ON / OFF(8 Zone, Alarm output) |
| Privacy |
| ON / OFF(12 Zone) |
| Mirror |
| H / V / BOTH / OFF |
| Clarity |
| ON / OFF(Level adjustable) |
D&N |
| ICR(COLOR / Black&White / AUTO) | |
| Stabilize |
| ON / OFF |
| Digital Zoom |
| ON(x16) / OFF |
DPC |
| 256 point(Even 128 point, ODD 128 point) | |
| Power Supply |
| Regulated 12V DC or 24V AC |
C | urrent Consumption |
| 150mA(LED OFF), 500mA(LED ON) |
| Operation Temp. |
| |
| Dimension |
| Ø150 x 98.6(H)mm |
| Weight |
| 1.76Ibs |
※The specification is subject to change without any prior notice to improve the quality.
◐FUNCTIONS
1. Setup for camera functions
①ENTER :
-Push the lever : Used to access the menu and confirm selection.
-Push the lever for one second : Open the menu or close the menu.
②Up, ③Down :
Used to move the cursor to up or down.
④Left, ⑤Right :
Used to move the cursor to left or right and change the value.
⑥EXT-VIDEO :
Extra video output terminal for installation.
Plug your test monitor in here. The cable is option.