Programming Procedure for SpectrumPlus tm Speed Dial Features

(Administrator Programmable Only) (Manual Entry of Characters)

The SpectrumPLUSTM Telephone has 11 one-touch speed dial locations that are convenient for dialing frequently used telephone numbers. This feature is under Administrative control so user changes do not occur.

?Speed dial programming must be done with the telephone plugged into the telephone line and power adapter.

?Programming can be performed with the telephone on-hook only.

?A maximum of 32 digits can be entered into ENTER NUMBER and 12 characters into ENTER NAME.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER NUMBER

Set up speed dial memory

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

locations with name and

 

 

 

 

 

 

 

12/01

PM

 

 

 

 

 

number entries. Check

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER NAME

 

verifies correct entry.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER ACCESS NO.

 

 

 

 

 

 

 

 

 

 

 

To Program Speed Dial Locations

Figure 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.Press and hold the “STORE” key for 6 seconds to activate Administrator mode. The words “ENTER

ACCESS NO.” will appear (figure 1).

12/01 PM

 

2.Next, press the speed dial location key where the desired location will be. The display will read

 

“Mxx NO CONTENT”. If the display shows a

 

M01 NO CONTENT

 

 

 

 

 

 

 

record, then there is a stored name and number in

 

 

 

 

 

 

that location (figure 2).

 

 

 

 

 

Figure 2

3.

Press the “STORE” key again and the display will

 

 

 

 

 

 

 

 

 

 

 

read “ENTER NUMBER” (figure 3).

 

 

 

 

 

 

4.

Using the dial pad, enter the number. Note that the

 

 

 

 

 

 

local area code is not required if AREA CODE is

 

 

12/01 PM

 

 

 

pre-programmed into memory.

 

 

 

 

 

 

 

 

 

 

 

 

5.

After entering the number, press the

“STORE”

 

 

 

 

 

 

key. The display will read

“ENTER

 

ENTER NUMBER

 

 

NAME” (figure 4).

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Using the keypad, enter the name associated with

 

 

 

 

Figure 3

 

the number being programmed and include the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flash, and/or Pause, when needed.

 

 

 

 

 

 

 

 

 

 

 

 

 

7.Press the “STORE” key to store the entry.

8.Program other speed dial locations, repeat 2 to 7.

9. To exit the program mode, press “DISC”.

12/01 PM

 

 

 

 

ENTER NAME

34

Figure 4

Page 35
Image 35
Spectrum Brands SP-550 manual Administrator Programmable Only Manual Entry of Characters, To Program Speed Dial Locations