Stanley Black & Decker 2005 Series Enter 1 2 3 4 5 6 #, unlock the safe, Enter 9 8 7 6 5 4 #

Operating Instructions

S&G® Z03 D-Drive™Multi-User Electronic Safe Lock

2005 Series

Opening the Lock		the time delay, for the opening code at the end of the time delay,
➥With No Time Delay		or for both codes. The silent alarm signal will be sent each time a
		duress code is entered. (Note: Lock codes 4 - 8 are not available if the
A valid code is needed to open the lock. This is how to open the		duress feature is turned on. If time delay override is disabled or not used, lock
lock with the original factory master code of 1 2 3 4 5 6. Make		code 9 is available.)
sure the keypad is turned counterclockwise to stop.		➥Using a Time Delay Override Code
Enter 1 2 3 4 5 6 #
		This lock is capable of using a time delay override code if it
Then, within six seconds, turn the keypad clockwise about
		was originally ordered with this feature, and if the TDO (time delay
70 degrees, until it comes to a positive stop. Do not put any
		override) feature is enabled. As the name implies, the time delay
pressure on the safe handle until after the keypad has been
		override code can be used to open the lock without waiting for
turned. To re-lock the S&G© X03 D-Drive™, turn the keypad back
		the time delay period to expire. This is useful for armored car cash
counterclockwise to stop. When the mechanism re-locks, it will emit a		pickups. The TDO code only works when your lock uses a time delay.
double beep consisting of a low tone followed by a slightly higher tone. If		Your lock is capable of two different types of time delay override.
you do not hear the double beep, the mechanism is not properly locked.
		Single control time delay override allows the TDO code holder to
➥With Time Delay Active		simply enter his code to open the lock. The time delay period is
		completely bypassed. For example, if the TDO code is 9 8 7 6 5 4,
Time delay enforces a waiting period between entry of the first
		it would only be necessary to press the following keypad buttons to
code and opening of the safe. This feature is a proven deterrent to
		unlock the safe.
armed robbery. Any valid lock code can be used to start the time
		Enter 9 8 7 6 5 4 #
delay. When this code is entered, the lock beeps three times and
		The other type of time delay override is dual control TDO. To use
begins counting down the delay period. The lock will beep once
every ten seconds during the delay period. At the end of the delay		this type of time delay override, it is necessary to start the lock’s
period, the lock will beep ten times rapidly. Enter a valid code		time delay by entering any valid code other than the TDO code.
for the lock. After the code is entered, the lock will release for six		Then, within one minute, enter the TDO code. The lock will open
seconds to allow you to turn the keypad and open the safe.		immediately. This type of time delay override places a secondary
➥With Duress Active		control on the TDO code holder, adding a measure of extra
		security. The following example uses the factory set master code
Duress , sometimes referred to as “silent alarm,” is a feature that		(1 2 3 4 5 6) to start the time delay, then a TDO code of 9 8 7 6 5
causes an alarm signal to be sent when a code is entered. This		4 is used to open the lock without waiting for the time delay period
capability must be enabled in the lock, and an optional duress		to expire.
module must be added to the lock and connected to an existing		Enter 1 2 3 4 5 6 #♪♪♪ 9 8 7 6 5 4 #
alarm system for this feature to work.		➥Useful Operating Information
A duress code (one which triggers the alarm signal) is simply
		The lock will emit a long error tone if an incorrect or incomplete
any valid lock code with 1 added to the last digit. For instance, if
you create a user code of 2 2 2 2 2 2, the duress version of this		code is entered. If five or more incorrect codes are entered in
code is 2 2 2 2 2 3. This code is valid for operating the lock and		a row, the lock will go into a ten-minute lockout period. If you
simultaneously triggering the duress alarm signal.		attempt to enter a code during this lockout period, two long error
When the duress feature is turned on, lock codes 0, 1, 2, 3, and		tones will be heard. Simply wait ten minutes, then attempt to
		operate the lock again. The lockout period cannot be bypassed. You
9 are capable of triggering the silent alarm signal. If a time delay
		must wait for it to time out.
is programmed into the lock, a duress code can be used to start
© Copyright 2006, Sargent & Greenleaf	Page 3