Manuals / Brands / Kitchen Appliance / Freezer / Stoelting / Kitchen Appliance / Freezer

Stoelting 513588R1 REPLACEMENT PARTS, SECTION, 5.1 HOW TO ORDER PARTS

1 41

Download 41 pages, 1.8 Mb

SECTION 5

REPLACEMENT PARTS

5.1 HOW TO ORDER PARTS

To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information:

A.Model number of equipment.

B.Serial number of model, stamped on nameplate

C.Part number, part name and quantity needed. Com- mon part names and numbers are listed in this manual.

Part Number	Description
208401	Brush, 2.54cm (1") diameter
208135	Brush, 10cm (4") diameter
208381	Brush, .95cm (3/8") diameter
208467	Brush, .80cm (5/16") diameter
324107	Decal - Hazardous Moving Parts
324105	Decal - Electrical Shock Hazard
324106	Decal - Applicable Electrical Code
324108	Decal - Caution
324141	Decal - Caution - Rotation Blade
324584	Decal - Adequate Ventilation
368140	Air Filter
508135	Petro-Gel Lubricant
508048	Spline Lubricant
Common Wearable Parts
381804	Auger Flights (5)
694255	Auger Flight Springs (5)
624598	O-Ring - Spigot (2)
625133	O-Ring - Door (1)
624607	O-Ring - Carburetor (2)
624678	O-Ring - Auger Rear Seal (1)
666786	Rear Seal w/insert (1)
149003	Front Auger Bushing (1)
232734	Rosette Cap (1)
152371	V-Belt (2)

21

Contents

Page Page Page Page STOELTING, LLC Tele: 502 Hwy Kiel, WI Fax: Page SECTION DESCRIPTION PAGE 1. INTRODUCTION 2. INSTALLATION INSTRUCTIONS FIGURE TITLE DESCRIPTION AND SPECIFICATIONS MODEL OPTIMA COUNTER MODEL GRAVITY FREEZER DIMENSIONS: WEIGHT: SECTION INSTALLATION INSTRUCTIONS 2.1SAFETYPRECAUTIONS Do not STOELTING, INC 2.2 SHIPMENT AND TRANSIT Donot Stoelting, Inc. cannot make any claims against the carrier 2.3FREEZERINSTALLATION Figure 4 - Leveling 2.4 FLOOR STAND INSTALLATION NOTE Figure 8 - Floor Stand 2.5 INSTALLING PERMANENT WIRING Figure 9. Power Cord Connection Page INITIAL SETUP AND OPERATION B.OFF-ONSWITCH C.PUSH TO FREEZE SWITCH D.GREENLIGHT E.CLEAN SWITCH F.DRIVE MOTOR OVERLOAD Figure 11. Mix Inlet Regulator Figure 12. Clean Control Figure 13. Sanitizing Hopper Figure 14. Draining Solution 3.4 FREEZEDOWNANDOPERATION Figure 15. Dispensing Product 3.5 MIX INFORMATION 3.6 REMOVING MIX FROM FREEZER Figure 16. Removing Mix Inlet Regulator Figure 17. Draining Mix 3.7 CLEANINGTHEFREEZER 3.8 DISASSEMBLY OF FREEZER PARTS Figure 18. Auger Flight Wear and Front Auger Support Bushing Wear Hopper Cover Figure 22. Auger Shaft Removal DO NOT USE ANY TYPE OF SHARP OBJECT TO REMOVE THE "O" RINGS Figure 23. Removing "O" Ring 3.9 CLEANINGTHEFREEZERPARTS DO NOT DAMAGE PARTS BY DROPPING OR ROUGH HANDLING Figure 26. Exploded View of Front Door FINGER TIGHTEN THE CIRCULAR KNOBS EVENLY. DO NOT OVERTIGHTEN KNOBS Figure 25. Spring Installation Figure 27. Mix Inlet Regulator 3.12ROUTINECLEANING 3.13PREVENTIVEMAINTENANCE A.Cleaning and Sanitizing Information Soil Materials Associated with Frozen Dessert Machines eventually defy sanitizing efforts This can lead to high bacteria counts and a food safety dilemma Additional Information THE USE OF DELIMERS PRODUCT SAFETY MACHINE DAMAGE DO NOT USE BLEACH D. MONTHLY E. SEMI-ANNUALLY 3.14EXTENDEDSTORAGE TROUBLESHOOTING CHARTS Page ERROR CODE SYSTEM CODE P.T.F. LIGHT FLASHES MEANING Page REPLACEMENT PARTS Page Page Page Page Page Page Page Page Page Page Page WARRANTY SOFT SERVE / SHAKE FREEZERS 1.Scope: 2.Disclaimer of Other Warranties: 3.Remedies: