SERVICING INSTRUCTIONS
SERVICING REQUIREMENTS
This appliance must be serviced at least one a year by a competent person.
1.servicing requirements
1.1As part of the annual service, the space behind the convector must be inspected for any debris, which may have fallen down the chimney.
1.2Remove the gas fire from the convector as detailed in section 4
1.3Remove the convector box from the wall, see section 5 in Installation.
1.3Inspect the space behind the convector for debris and the condition of the chimney, the flue flow test should be carried out now. Remove any debris and carry out any necessary remedial work.
FLAME FAILURE FUNCTIONAL CHECK
PILOT WILL NOT STAY LIT OR FIRE GOES OUT
If the appliance goes out in use continually, this may mean
that the
oxygen depletion sensor has been activated. The appliance
should not be used
until the cause has been found and rectified.
Ensure there is no debris around the pilot assembly, e.g.
coal, soot, etc.
Check for fluff in the pilot aeration hole. See Diagram 7.
Light the pilot and keep the control knob pushed in at least
10 seconds before letting go
2. fault finding
This is for use only by qualified Installers and Service Engineers.
Note: Many problems can be attributed to poor pilot flame length caused by blocked jets as the orifice is very small. If the flame length is much shorter than that shown in the Diagram, the pilot may have to be changed. See Diagram 7.
It is always worth using the nozzle of a vacuum cleaner over the end of the pilot to ensure that it has no debris within it. In addition, many ignition problems are caused by incorrect spark
With the pilot running is the gas pressure as
stated on the
databadge?
YES
NO
NO
Will the pilot YES stay lit? 
NO
Problem is with
the pipework
or
fittings which
lead to the fire. Correct and retry
With the fire
running on
full is
the gas at the
pressure
stated on the databadge
Run for 60 |
|
sec’s., | YES |
|
gap, ensure it is set as in Diagram 7.
7
AR0097
| Is the pilot |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| Is |
|
| NO | |||||||
| flame of the |
|
|
|
|
| ||||||||
| correct |
|
| thermocouple |
|
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||||
| length? |
|
| connection |
|
|
|
|
|
| ||||
| See Diagram |
|
|
| good |
|
|
|
|
|
| |||
| 7. |
|
| in back of |
|
|
|
|
|
| ||||
|
|
|
|
|
| valve |
|
|
|
|
|
|
| |
|
|
|
| YES |
|
| NO | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Replace |
|
|
|
|
|
| ||
|
| NO |
|
| ODS unit |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| YES | ||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| Will the pilot | |||||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| stay lit? |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| NO | |||||
|
|
|
|
|
| Change |
|
| NO | |||||
| Change the |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||
| ODS unit |
|
| mag unit |
|
|
|
|
|
| ||||
turn off, time |
interval until |
mag unit |
shuts with a |
click. Is this |
greater |
than 7 |
seconds? |
NO |
Tighten the |
connection |
and retry |
YES
Run for 60
sec’s.,
turn off, time interval until mag unit shuts with a click. Is this greater than 7 seconds?
SYSTEM O.K
19
