STOW T-30H — MAINTENANCE (PUMP)

Pump Vacuum Test

CAUTION :

DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed.

To perform the pump vacuum test do the following:

1.Remove the pump fill cap (Figure 2), and fill the pump with water.

2.Start the engine as outlined in the initial start-up section, and wait for the pump to begin pumping.

3.As shown in Figure 17 (next page), place a water hose inside the discharge opening of the pump, and turn on the water. This flow of water into the discharge opening will prevent the pump from running dry.

4.Place the Pump Vacuum Tester (P/N 7000030) over the pump suction (inlet) opening (Figure 17) with the vacuum gauge facing upwards. It may be necessary to apply a small amount of water around the rubber seal of the vacuum tester to make a good suction fit.

5.Check and make sure that there are no air leaks between the vacuum tester and the inlet port on the pump. If air leaks are present reseat vacuum tester.

6.Run the pump for a few minutes while monitoring the vacuum gauge. If the gauge indicates a reading between -25 and -20 in. Hg. (inches of mercury) then it can be assumed that the pump is working correctly.

25 in. Hg (inches of mercury)

NOTE translates into 25 feet of lift at sea level.

7.If the vacuum tester gauge indicates a reading below -20 in. Hg, it can then be assumed that the pump is not functioning correctly, and corrective action needs to be taken.

6.To test the flapper valve, shut down the engine. The vacuum tester should remain attached to the pump suction inlet port by vacuum. This indicates the pump's flapper valve is seating properly to hold water in the suction hose when the engine is stopped.This prevents backflow and allows for faster priming when the engine is restarted.

Adjusting Impeller Clearance

1.If it is necessary to replace impeller or volute, be sure clearance between impeller and volute is adjusted correctly.

2.The impeller should be as close to the volute as possible without rubbing against it. Clearance is adjusted by adding or removing shims from behind the impeller.

3.Check clearance between impeller and insert by slowly pulling starter rope to turn impeller. Remove spark plug to make it easier to turn impeller.

It is important not to remove too many shims or the clearance

NOTE between the impeller and volute will become too wide and pump performance will be reduced. Remember as the impeller wear

down, additional shims may be required to maintain the clearance between the impeller and insert.

4.Check the impeller every six months for wear, and for clearance between the impeller face and the volute. Also check the shaft seal for wear, as well as the shaft sleeve.

Pump Cleaning

After pumping water containing large amounts of dirt and debris, perform the following:

1.Remove the drain plug from the pump housing (Figure 2) and drain any water left in the pump.

2.Loosen the two locking hand knobs (turn counter- clockwise) and remove clean-out cover.

3.Clean and remove dirt, debris from pump casing. Inspect impeller and volute for wear. Replace any damaged or worn parts.

CAUTION :

The impeller may develop sharp edges. Use extreme care when cleaning around the impeller to prevent being cut.

PAGE 20 — STOW T-30H TRASH PUMP — PARTS MANUAL — REV. #0 (05/30/03)

Page 19 Page 21
Page 20
Image 20
Stow manual Stow T-30H Maintenance Pump, Pump Vacuum Test
Page 19 Page 21

T-30H specifications

The Stow T-30H is an advanced stadium and event venue turbine heater that combines efficiency, performance, and cutting-edge technology, making it a preferred choice for a range of applications. Designed specifically to provide optimal heating solutions in large spaces, the T-30H stands out due to its unique features and functionalities.

One of the primary features of the Stow T-30H is its robust heating capacity. With a heating output that can reach up to 30 kW, the unit is capable of efficiently warming areas of significant size. This makes it particularly suitable for indoor sporting events, exhibition halls, and outdoor venues during the colder months. The heater is also engineered to quickly and effectively raise the temperature in a controlled manner, ensuring that users remain comfortable in any setting.

The T-30H incorporates innovative technology designed to maximize its efficiency. It utilizes an advanced combustion system that not only improves fuel consumption but also minimizes emissions. This eco-friendly approach aligns with modern sustainability goals, making the heater an attractive choice for organizations aiming to reduce their carbon footprint.

The ease of operation is another noteworthy characteristic. The Stow T-30H features a user-friendly control panel that allows operators to set and adjust the heating levels conveniently. Additionally, it includes built-in safety mechanisms, such as overheat protection and flame failure detection, ensuring safe operation at all times.

Portability is key in the design of the T-30H. The unit is equipped with durable wheels and a compact profile, allowing for easy transportation and set-up across different locations. This makes it an ideal solution for event organizers who need a heating solution that is both efficient and flexible.

Furthermore, the Stow T-30H is compatible with various fuel sources, offering versatility for users. With options for propane, natural gas, and diesel, it can cater to diverse operational needs and preferences.

In summary, the Stow T-30H delivers powerful heating capabilities combined with modern technology and user-friendly operation. Its focus on efficiency, safety, and portability makes it an excellent choice for stadium and event venue heating needs, ensuring comfort for participants and audiences alike. With this remarkable heater, organizations can enhance the experience of their events, no matter the season.
Top Page Image Contents