Troubleshooting

continued from previous page

Poor Water Flow:

1.Clean filter

2.Check if adjustable jets (are all open)

3.May have air lock, prime pump by loosening top pump union.

4.If water diverted valves are present make sure they are all the way open.

5.If gate valves are present, make sure they are all the way open.

6.If none of this works possible line obstruction or impeller loose on pump drive shaft

No water or air flow to jet:

1.If adjustable jets, probably in off position. (At times can lock into position, may require some effort.)

2.Pinched line, cutting off flow before reaching spa.

3.Water diverter valve if present may be closed.

Air controls not working:

1.Remove cap on air valve, (with flat head screw driver) and make sure not broken or improper alignment.

2.If internals are broke, call tech support

Jets Only Have One Speed:

1.Check pump connection at pack make sure power off (red plug.)

2.Programming error, call Tech Support.

3.Button not working properly, call Tech Support

Light Not Working:

1.Check for proper connection on pack and in line at red alligator clips.

2.Check for proper connection at light.

3.Call Tech Support

Heat not working: (No blinking decimal in lower right corner of control display)

1.Check desired temperature is higher than current temperature.

2.Make sure Jets are on low speed

3.Aux must also be turned off.

Heat not working: (Blinking decimal, but no heat)

1.Give spa time to heat up and be sure to cover.

2.Bad heater, call tech support

Water temperature not close to displayed temperature:

1.Check thermister is located in thermalwell and insulated by rubber gasket.

2.Make sure that air vents are unobstructed.

LOC

1. Press Heat and Jets key simultaneously. This will activate and deactivate this code.

Display flashes “FLO” (FLOW)

1.This indicates that there is a water flow problem or defective pressure switch.

2.Make sure filters are clean

3.Check that service valves are open

4.Check for obstruction of flow

5.Adjust pressure switch (see pressure switch detail under description and use of controls)

Freeze Protect Over-ride FPO

This function is intended to be used on start-up after a fresh fill if water temp is below 52ºF. The 6 hour duration of the FPO cycle is counted from the time the unit is powered-up and not from the time of its activation.

By pressing the Jets 1 and Light key simultaneously for 10 seconds, the freeze protect feature will be suspended for 6 hours. ( the FPO will be activated) This is to allow the installer of the spa to check for normal operation if the spa is filled with water that is less than the set freeze protect level 52ºF. FPO will appear every 10 seconds at the topside control. To manually go back to freeze protect mode, power down the system and re-boot. It is recommended that the system be left on low speed and heating in FPO mode.

8

Page 9 Page 11
Page 10
Image 10
Strong Pools and Spas Rotational Molded resin whirlpool spa owner manual Loc
Page 9 Page 11

Rotational Molded resin whirlpool spa specifications

Strong Pools and Spas offers an innovative solution for relaxation and rejuvenation with their Rotational Molded Resin Whirlpool Spa. This spa exemplifies the perfect combination of durability, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to elevate their outdoor experience.

One of the standout characteristics of the Strong Pools and Spas Rotational Molded Resin Whirlpool Spa is its high-quality construction. The rotational molding technique used in its manufacturing ensures that the resin is uniformly distributed, creating a seamless structure that is not only robust but also lightweight. This process enhances the spa's resistance to cracking and fading, providing a long-lasting investment for any backyard.

The whirlpool spa is designed with a focus on user comfort and experience. Featuring strategically placed jets, it delivers a powerful hydrotherapy massage, targeting sore muscles and providing relief after a long day. The adjustable jet system allows users to customize their experience, choosing the intensity of the massage that best suits their needs.

Another key feature is the easy-to-use digital control panel, which offers intuitive operation for managing temperature and jet functions. Additionally, the spa is equipped with energy-efficient technology, including a high-performance heater and a well-insulated shell, ensuring minimal energy consumption while maintaining optimal water temperature.

Safety is also a prime consideration in the design of Strong Pools and Spas. The whirlpool spa comes with built-in ergonomic seats that provide secure and comfortable seating while allowing ample space for relaxation. Furthermore, the textured surface around the spa enhances grip, significantly reducing the risk of slips and falls.

Maintenance is made effortless with the spa's advanced filtration system, which helps keep the water clean and clear. The design also allows for simple drainage and refilling, so users can easily maintain their spa with minimal hassle.

In conclusion, the Strong Pools and Spas Rotational Molded Resin Whirlpool Spa stands out with its durable construction, customizable comfort features, and energy-efficient operation. This spa not only enhances outdoor aesthetics but also promotes wellness and relaxation, making it a valuable addition to any home.
Top Page Image Contents