Changing Filter Cycles

FILTRATION

Proper filtration is an important key to maintaining the clarity of your spa's water. The filter system is designed for unsurpassed effectiveness at removing debris and suspensions from the water anytime the water is circulating.

Your control panel is set to filter for two hours every twelve hours. A two speed pump is sup- plied with your spa that provides filtration on low speed, the low speed will shut off if the tem- perature creeps more than 2 degrees above the set point, it will turn back on when tempera- ture drops to the set point.

Press Heat key and Auxiliary key simultaneously and hold to adjust the filter cycle form the two hours every 12 hours period.

Troubleshooting

*indicates qualified service technician recommended

Heat Mode 120V Version

In LC ( Low Current ) Mode ( 120V versions ): Jets 1 must be in low speed and AUX (optional pump 2 or blower) must be off before heater can be turned on.

If the red indicator DOT in the bottom right of your temperature window is not flashing when there is a demand for heat, press the AUX key to shut off the optional secondary pump / blower circuit. This secondary circuit will automatically shut off in 30 min if left on.

No display at topside*

•Check that connection to main board is clean and sound at J8.

•Test a new topside control

•Check for 120V primary power going into the transformer and for 12V secondary power out of the trans- former to J6 and J7 on the board before replacing the transformer.

•Relace board if there is 12V to J6 and J7.

Display flashes “th1/38” on system start up*

•Check that temperature sensing probe connection to main board is clean and sound at location J2.

•Try new temperature sensing probe.

Display flashes “th2/current temperature” on system start up*

•Check that the temperature sensing probe connected to the main board is clean and sound at location J1.

•Try new temperature sensing probe.

Display flashes “th2/39” on system start up

•This indicates that both sensors ( thermisters ) are detecting tub water temperature of less than 39F or they are both disconnected ( open ). Pump(s) will run in this condition. See Freeze Protect Override (FPO) instructions for cold water fill up.

Display flashes”OH” (OVERHEAT)

•This indicates that the spa water temperature is over 112ºF. The system should be shut down in this state and will re-start automatically when the water cools below 112ºF.

7

Page 8 Page 10
Page 9
Image 9
Strong Pools and Spas The Cyprus owner manual Changing Filter Cycles, Troubleshooting
Page 8 Page 10

The Cyprus specifications

Strong Pools and Spas, located in the beautiful locale of Cyprus, is renowned for its exceptional quality and innovative designs in the realm of pool and spa solutions. Catering to both residential and commercial spaces, Strong Pools and Spas offers a comprehensive range of products that combine aesthetics, durability, and cutting-edge technology.

One of the main features of Strong Pools and Spas is their extensive selection of customizable swimming pools. Customers can choose from a variety of shapes, sizes, and depths, ensuring that each pool is tailored to suit individual preferences and site conditions. The design options encompass everything from sleek modern styles to more traditional aesthetics, allowing each installation to blend seamlessly with its surroundings.

The technology utilized in Strong Pools and Spas is among the best in the industry. Their pools are equipped with advanced filtration systems that ensure crystal-clear water while minimizing maintenance requirements. Innovative automation technologies allow users to control heating, lighting, and water features remotely via smartphones or tablets, promoting convenience at the touch of a button. Additionally, eco-friendly options are available, including energy-efficient pumps and solar heating systems, reflecting Strong Pools and Spas' commitment to sustainability.

In terms of spa offerings, Strong Pools and Spas features a range of hot tubs and whirlpools designed for relaxation and rejuvenation. Their spas come with state-of-the-art hydrotherapy jets, ergonomic seating, and mood-enhancing LED lighting, creating a serene oasis right in your backyard. The use of durable materials ensures longevity, while a variety of finish options allows for personalization.

Durability is another cornerstone of Strong Pools and Spas products. Constructed with high-quality materials, their pools and spas are designed to withstand the challenges of the Cypriot climate, ensuring that they remain in prime condition for years to come. This commitment to quality is reflected in strong warranties and customer support, giving clients peace of mind in their investment.

In conclusion, Strong Pools and Spas stands out in Cyprus for its blend of customizable options, advanced technology, and durable construction. Customers seeking to create a tranquil oasis with a beautiful pool or spa will find reliable solutions in Strong Pools and Spas, making their dream of outdoor perfection a reality.
Top Page Image Contents