SUPER MICRO Computer x10slq, x10slq-l Motherboard Features

Chapter 1: Introduction

1-7

Notes:

1. CPU Overclocking is supported by this motherboard; however, SMCI does not recommend CPU Overclocking and cannot

resume any responsibility or liability of out_of_spec. overclocking.

2. CATERR_LED is for internal testing only.

Motherboard Features

CPU 4th Generation Intel® Core™ i7/i5/i3, Pentium, and Cel-

eron processor in an LGA1150 socket.

Memory Four (4) SDRAM slots support up to 32 GB of DDR3 Unbuf-

fered, Non-ECC 1600/1333 MHz memory for the X10SLQ.

Two (2) SDRAM slots support up to 16 GB of DDR3

Unbuffered, Non-ECC 1600/1333 MHz memory for the

X10SLQ-L.

Dual-channel memory

DIMM sizes

UDIMM 1 GB, 2 GB, 4GB, and 8GB

Chipset Intel® Q87 Express

Expansion Slots One (1) PCI Express 3.0 x16 slot (Slot 7)

One (1) PCI Express 2.0 x1 slot (Slot 5)

One (1) PCI Express 2.0 x4 slot (Slot 4)

Network Connections Two (2) Gigabit Ethernet Controllers:

LAN1: Intel i217LM gigabit LAN PHY

LAN2: Intel i210AT gigabit LAN controller

Two (2) RJ-45 rear I/O panel connectors with Link and

Activity LEDs

I/O Devices SATA Connections

SATA 3.0 (6Gb/s) Six (6) I-SATA 0-5, via Intel PCH Q87,

SATA Port 5 to mSATA

RAID 0, 1, 5, 10 (MS Windows®)

USB Devices (USB 0/1 and 10/11: Not available on

the -L model)

Four (4) USB 2.0 ports on the rear I/O panel (USB 0/1,

4/5),

Two (2) USB 3.0 ports on the rear I/O panel (USB 2/3)

Four (4) Front Accessible USB 2.0 ports on two headers

(USB 6/7, 8/9),

Two (2) Front Accessible USB 3.0 ports on one header

(USB 10/11)

Keyboard/Mouse (Not available on the -L model)

One shared PS/2 Keyboard/Mouse port on the I/O

backpanel

Serial (COM) Ports

Four (4) front accessible Serial Port header (COM1-

COM4) (COM2 supports RS232/422/485)

Contents

Main Printed in the United States of America iii Preface About This Motherboard Manual Organization Conventions Used in the Manual: v Contacting Supermicro vi Table of Contents Preface Chapter 1 Introduction Chapter 2 Installation vii Page 1-1 Chapter 1 Introduction 1-1 Overview Checklist Page Chapter 1: Introduction 1-3 X10SLQ/X10SLQ-L Motherboard Layout Important Notes to the User panel connections. plug the power cable before installing or removing any components. X10SLQ (-L) 1-4 X10SLQ (-L) X10SLQ/X10SLQ-L Quick Reference 1-5 Page 1-7 Motherboard Features 1-8 Page 1-10 X10SLQ/X10SLQ-L Block Diagram PCH INTEL LGA1150 Page 1-12 1-3 Special Features Recovery from AC Power Loss 1-4 PC Health Monitoring Fan Status Monitor with Firmware Control Environmental Temperature Control 1-5 ACPI Features Slow Blinking LED for Suspend-State Indicator 1-6 Power Supply 1-14 1-7 Super I/O 2-1 Chapter 2 Installation 2-1 Standardized Warning Statements Battery Handling Page Page 2-4 2-2 Static-Sensitive Devices Precautions Unpacking Page Page 2-7 2-8 Installing an Active CPU Heatsink with Fan 2-9 2-10 Removing the Heatsink Active Heatsink Removal 2-11 2-4 Installing DDR3 Memory CAUTION DIMM Installation 2-12 2-13 2-14 X10SLQ (-L) 2-5 Motherboard Installation Location of Mounting Holes Tools Needed Philips Screwdriver (1) Standoffs (8) Only if Needed Installing the Motherboard 2-16 HD Audio X10SLQ (-L) 2-6 Connectors/IO Ports R O L I AB 2-18 Note: USB 0/1 and 10/11 are not available on the -L model. C G 2-19 (NC: No Connection) A. LAN1 B. LAN2 C. SPDIF_Out D. Surround_Out E. CEN/LFE_Out F. Mic_In G. Line-Out H. Line_In (BP) HD Audio Conn# Signal ASPDIF_Out BSurround_Out CCEN/LFE_Out DMic_In ELine_Out FLine_In 2-20 2-21 A. VGA Port B. DVI-D X10SLQ (-L) 2-22 Front Control Panel Pin 15Pin 16 Pin 2 LED 1 Front Control Panel Pin Denitions Power LED Pin# Denition 15 +5V 16 Ground A. PWR LED B. HDD LED HDD LED 2-24 C LAN1/LAN2 LED Pin# Denition 9/11 Vcc 10/12 Ground 2-25 Power Button Pin# Denition 1 Signal 2+3V Standby Reset Button Pin# Denition 3 Reset 4 Ground 2-7 Connecting Cables A. 24-Pin ATX Main PWR B. 4-Pin PWR 12V 4-pin Power Connec- tor Pin Denitions Pins Denition 1/2 Ground 3/4 +12V A B 2-27 X10SLQ (-L) A. Fan 1 (CPU Fan) B. Fan 2 C. Fan 3 D. Fan 4 E. Chassis Intrusion Chassis Intrusion Pin Denitions (JL1) Pin# Denition 1 Intrusion Input 2-28 A. Internal Buzzer B. Speaker Header Speaker Connector Pin Setting Denition Pins 3-4 Internal Speaker Pins 1-4 External Speaker 2-29 A. PWR LED B. COM1 C. COM2 D. COM3 E. COM4 Serial/COM Ports 2-30 DOM PWR Pin Denitions Pin# Denition 15V 3 Ground A.DOM PWR B. JWOR1 2-31 A. TPM/Port 80 B. Standby PWR Header 3No Connection Standby Power Header Standby Power 2-32 A. T-SGPIO 1 B. T-SGPIO 2 C. BIOS Recovery 2-33 2-8 Jumper Settings Explanation of Jumpers A. JPL1: LAN1 Enable B. JPL2: LAN2 Enable GLAN Enable Pin# Denition 1-2 Enabled (default) 2-3 Disabled 2-34 A. Clear CMOS B. JI2C1 C. JI2C2 2-35 A. Audio Enable B. Watch Dog Enable Audio Enable/Disable Both Jumpers Denition Pins 1-2 Enabled Pins 2-3 Disabled Watch Dog 2-36 A. ME Recovery ME Recovery Jumper Settings Jumper Setting Denition 1-2 Normal (Default) 2-3 ME Recovery 2-37 A. BIOS Recovery 2-38 A. LAN 1/2 LEDs B. PWR LED 2-9 Onboard Indicators Activity LED Link LED 2-39 2-10 SATA Connections Note: mSATA is not available on the -L model. SATA 3.0 Connectors Pin# Signal 1 Ground 2 SATA_TXP 3SATA_TXN 4 Ground 5SATA_RXN 6 SATA_RXP 7 Ground A. I-SATA 3.0 #0 B. I-SATA 3.0 #1 C. I-SATA 3.0 #2 D. I-SATA 3.0 #4 E. I-SATA 3.0 #3 Page 3-1 Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Before Power On No Power 3-2 No Video Memory Errors Losing the Systems Setup Conguration 3-3 3-2 Technical Support Procedures 3-3 Frequently Asked Questions 3-4 3-5 3-4 Battery Removal and Installation Battery Removal Proper Battery Disposal 3-6 OR 3-5 Returning Merchandise for Service Battery Installation 4-1 Chapter 4 BIOS 4-1 Introduction Starting BIOS Setup Utility How To Change the Conguration Data 4-2 4-2 Main Setup 4-3 4-4 4-3 Advanced Setup Congurations 4-5 Power Conguration Page 4-7 4-8 4-9 4-10 4-11 4-12 4-13 Page 4-15 4-16 4-17 4-18 4-19 4-20 Module is Detected) 4-21 AMT (Active Management Technology) Conguration 4-22 Page 4-24 Console Redirection Settings 4-25 4-26 4-27 4-4 Boot Settings Page 4-29 4-5 Security Settings 4-30 4-6 Save & Exit 4-31 Page A-1 Appendix A BIOS Error Beep Codes A-1 BIOS Error Beep Codes BIOS Error Beep Codes Page B-1 Appendix B Software Installation Instructions B-1 Installing Drivers B-2 B-2 Conguring SuperDoctor III Page Page C-1 Appendix C UEFI BIOS Recovery Instructions C-1 An Overview to the UEFI BIOS C-2 How to Recover the UEFI BIOS Image (the Main BIOS Block) C-3 To Recover the Main BIOS Block Using a USB- Attached Device C-2 Page Page D-1 Appendix D Dual Boot Block D-1 Introduction BIOS Boot Block BIOS Boot Block Corruption Occurrence