These operations are accessible by remote control.

Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, press POWER to turn on the unit.

•It may take a few moments to turn on the unit for the first time.•[Initial Setup] menu appears automatically after the unit is turned on.

2 Use ▲/▼ to select the on-screen language from the choices (English/Español/Français) on the right side of the TV screen, then press ENTER.

3 Use ▲/▼ to select [Antenna] for TV channels or [Cable] for CATV channels, then press ENTER.

Initial Setup

Make sure the antenna is connected to ''ANT. IN'' jack.

Antenna

Cable

Select your signal source.

 

 

 

 

 

Skip

Antenna

 

 

 

Cable

Or

ANT.IN

 

 

 

 

Select

ENTER Enter

Back

Skip

•[Autoprogram] will begin.

Initial Setup

Please wait while the system is scanning for channels. Auto programming may take more than 20 minutes to complete.

0%

Digital channels

0 ch

 

 

 

 

 

 

 

 

 

 

 

Analog channels

0 ch

 

 

 

 

 

 

Skip

 

 

English

 

 

13

 

 

 

 

 

 

4 Use ◄/► to select the desired location setting, then press

INTRODUCTION

 

ENTER.

 

 

 

 

 

 

Initial Setup

 

 

 

 

 

 

 

Select “Retail” or “Home” for your location.

Select

ENTER Enter

PREPARATION

Retail

Home

 

 

• Select [Retail] store, the unit will be set up with

 

 

 

predefined setting for retail displays. In this setting, the

WATCHING

 

 

power consumption may possibly exceed the limited

 

 

requirement of the ENERGY STAR® qualification.

 

• Select [Home], the unit is set to maximize the energy

 

 

efficiency for home setting and it can be adjusted

 

 

TV

 

 

through a choice of picture and sound quality according

 

 

to your preference.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• When the initial setup is completed, the lowest

 

 

USING

 

 

memorized channel with the confirmation message of

 

 

the location setting will be displayed on the TV screen.

 

 

 

 

 

 

 

FUNCTIONS

Note

 

 

 

 

 

• If you are not receiving a signal from your cable service, contact

 

 

the Cable provider.

 

 

 

 

 

• If you press POWER or SETUP during autoprogram, this setting

 

 

 

 

will be canceled.

 

 

 

 

 

 

•

The initial autoprogram function can be executed for either

 

OPERATING

 

[Antenna] or [Cable] only once.When you change the

 

•

connection (Antenna / Cable), set [Autoprogram] again. ➠ p.19

 

If there is no signal input from the antenna terminal and no

 

 

operation for several seconds after you turn on the unit, helpful

 

 

 

DVD

 

hints appears. Follow the instructions listed on the TV screen.

 

 

 

 

 

 

 

 

 

 

 

Initial Setup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Retry

 

 

CONNECTING

 

 

No channel is registered.

 

 

Later

 

 

 

 

Try Autoprogram again?

 

 

 

 

 

 

 

Verify that you have a cable connected to the “ANT. IN” jack

 

 

 

 

 

on the back of the TV, the channel installation process

 

 

 

 

 

 

searches this connection. If you are using a cable or satellite

 

 

 

 

 

box, please confirm the input which you have connected to the

 

 

 

DEVICES

 

 

box and press “INPUT SELECT” key on the remote control to

 

 

 

 

 

select the appropriate source input.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select

ENTER Enter

Skip

 

 

 

 

 

 

 

 

 

 

 

 

 

USEFUL

• You must set [Home] in step 4. Otherwise, [Picture] and [Sound]

 

 

settings you adjusted will not be memorized after the unit goes

 

 

into standby mode.

 

 

 

 

 

 

 

 

 

 

 

TIPS

After an initial setup is completed

 

 

 

 

 

 

 

 

 

 

• If you want to scan the channels automatically again.

 

 

 

[Autoprogram] ➠ p.19

 

 

 

 

INFORMATION

 

• You can add the desired cable and analog channels

 

 

 

 

unmemorized by autoprogram.

 

 

 

 

 

 

 

[Add Channels] ➠ p.20

 

 

 

 

 

 

• If you want to change to another language.

 

 

 

[Language] ➠ p.24

 

 

 

 

 

 

 

• If you want to change the location setting.

 

 

 

[Location] ➠ p.24