38
FAQ
| Question | Answer | ||
| • Check the antenna or cable connection to the main unit. | ||
| • Check the batteries of the remote control. | ||
| • Check if there is an obstacle between the infrared sensor window and the remote control. | ||
| • Test the signal output. If okay, then possible infrared sensor trouble. [IR Signal Check] ➠ p.39 | ||
My remote control does not work. | • Aim the remote control directly at the infrared sensor window on the front of the unit. | ||
What should I do? | • Reduce the distance to the unit. | ||
• | |||
| |||
| • When there is an | ||
|
| control signal of this unit. | |
| • Move the | ||
|
| turn off the infrared communication function. | |
How come the Initial setup | • Connect the RF coaxial cable to the unit directly and run the initial setup. | ||
appears every time I turn on this | |||
• Make sure to complete the channel scan before the unit goes into standby mode. | |||
unit? | |||
|
| ||
| • Make sure [Autoprogram] has been completed. ➠ p.19 | ||
| • Autoprogram must be completed when you set up the unit for the first time or move it to a location | ||
|
| where previously unavailable channels are broadcast. | |
Why can I not watch some RF | • The selected channel may not be broadcasting. | ||
• When [Autoprogram] is interrupted and not completed, some channels will not be received. Make | |||
signal TV programs. |
| sure to complete the Autoprogram. ➠ p.19 | |
| • The selected channel cannot be viewed by the [Child Lock] setting. ➠ p.21 | ||
| • The unit requires some kind of antenna input. An indoor antenna (VHF / UHF), an external antenna | ||
|
| (VHF / UHF) or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the | |
|
| unit. | |
| • Check if the correct input mode is selected by pressing INPUT SELECT or using CH ▲/▼. | ||
How come there is no image from |
| [Switching Each Input Mode] ➠ p.14 | |
• Check the antenna or cable connection to the unit. | |||
the connected external devices? | • When using the Component Video Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/ | ||
|
| Cr) connectors are connected to their corresponding colored jacks on the unit. | |
When I enter a channel number, it | • Many digital channels have alternate channel numbers.The unit changes the numbers automatically to | ||
| the ones signifying the broadcasting station channel number.These basic numbers used for previous | ||
changes automatically. |
| ||
| analog broadcasts. (e.g., input ch#30 auto changes to ch#6.1) | ||
|
| ||
| • | Clean the disc. | |
| • Ensure the disc is correctly inserted. | ||
My disc cannot be played back. | • Check if the disc is defective by trying another disc. | ||
Is there any way I can play my disc? | • Cancel the parental lock or change the control level. | ||
| • Insert a correct disc that plays back on this unit. | ||
| • Handle a disc with special care so that it does not have fingerprints, scratches or dusts on its surface. | ||
Why are captions not displayed | • Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts. | ||
| Most captioning production companies can display a dialog to maximum of 220 words per minute. If | ||
entirely? Or, captions are delayed |
| ||
| a dialog exceeds that rate, selective editing is used to insure that the captions remain | ||
behind the dialog. |
| ||
| the current TV screen dialog. | ||
|
| ||
How can I set the clock ? | • There is no clock function on this unit. | ||
I cannot change the [Child Lock] | • | If a Power failure occurs for longer than 10 seconds the child lock setting is retained, but the PIN code | |
setting because my PIN code no | |||
| is set to the default code “0000”. [Child Lock] ➠ p.21 | ||
longer works. |
| ||
|
| ||
|
|
| |