Symphonic WF206 Preparation For Use, Operations, Connections, Installing The Batteries

Models: WF206

1 8
Download 8 pages 26.02 Kb
Page 2
Image 2
PREPARATION FOR USE

PREPARATION FOR USE

CONNECTIONS

You can enter into Video mode from Game mode by adjusting a Picture control.

Plug the incoming cable into the ANT. jack on the rear of the TV.

1To use external input

2To cancel Game mode only

Cable OR Antenna

TV signal

Incoming cable from home Antenna /

Cable Company (No Cable Box)

Cable Box or

Satellite Box*

OR

OUT

IN CONNECTIONS

Rear of this TV

ANT.

GAME

GAME

Picture: GAME (ON)

Input: External

MENU

m

[-]

GAME MODE [+]

VOL

OFF

ON

 

 

Select “PICTURE”

 

After 10 seconds

VIDEO

 

Picture: Customized

Incoming cable from Cable

*Note (DO NOT DISCONNECT FROM BOX)

Company or Satellite Antenna

Some cable TV systems use scrambled signals and

Cables not included

require a special converter to receive these channels.

Consult your local cable company.

 

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Note:

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack before moving the unit.

Input: External

3To return to TV channel

15

GAME

2 times

OPERATIONS

REMOTE CONTROL AND FRONT PANEL FUNCTION

[EXTERNAL CONNECTION]

AUDIO/VIDEO input

ex.

 

 

Audio Cable

Rear of this TV

 

 

(OUT)

(IN)

 

 

 

AUDIO

 

 

 

VIDEO

Video Camera

Video Game

(OUT)

(IN)

Video Cable

 

 

 

 

INSTALLING THE BATTERIES

 

1

2

3

Install two AAA batteries (not supplied)

 

 

 

matching the polarity indicated inside

 

 

 

battery compartment of the remote

 

 

 

control.

[BATTERY PRECAUTIONS]

• Be sure to follow the correct polarity as indicated in the battery compartment.

Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries

IR transmitter

 

 

 

To send infrared ray (IR) signal

 

 

 

 

 

 

GAME

POWER button

 

 

 

To turn TV on/off

POWER

 

 

VOL X/Y buttons

 

o

CH

m

 

p

To adjust volume

VOL

n

 

To decide the command of settings

1

2

3

 

 

4

5

6

 

7

8

9

MENU button

MENU

0

+100

To view on-screen menu

 

 

 

MUTE button

MUTE

SLEEP

CH RET

To mute sound

 

 

 

DISPLAY button

 

DISPLAY

 

 

 

 

To display CH No./Audio Status

 

 

 

GAME button

Press to set the Game mode.

CH K/L buttons

To select channels and move up/down through menu items

Channel number buttons

Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button

Press to select cable channels higher than 99.

SLEEP button

To set Sleep Timer

CH RET button

To return to previous channel

with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent

damage or injury from possible battery leakage.

• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

Note:

You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)

INITIAL SETUP

When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.

1 Select the desired

SELECT LANGUAGE

 

2 If the TV screen shows

- HELPFUL HINTS -

language according to

 

snow noise and there

1. PLEASE CHECK TO SEE IF

ENGLISH

 

SATELLITE IS PROPERLY

 

 

 

 

THE ANTENNA/CABLE/

the screen indication.

NEXT:PRESS CHK

 

is no operation for

CONNECTED.

ESPAÑOL

 

2. DID YOU PERFORM

After that, the TV

DESPUÉS:PRESIONE CHL

 

more than 10 seconds,

“AUTO PRESET CH” ?

APRÈS:PRESSEZ VOLK

 

PAGE OF THE OWNER’S

 

FRANÇAIS

 

 

3. PLEASE REFER TO FRONT

performs “AUTO

 

 

“HELPFUL HINTS”

MANUAL OR REAR PANEL

 

 

FOR SUPPORT LINE

PRESET CH” to scan

 

 

appears. Follow the

INFORMATION.

 

 

 

channels available for

– INITIAL SETUP –

 

instructions listed on

 

the broadcasting in

PLEASE CONNECT ANTENNA

 

the screen.

 

OR CABLE OR SATELLITE

 

 

your area.

TO THIS UNIT.

 

 

 

THEN PRESS CH K,

 

 

 

 

 

 

 

 

IN ORDER TO PERFORM

 

 

 

 

“AUTO PRESET CH”.

 

 

 

 

 

 

 

 

When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.

Notes:

In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.

If those settings do not work properly, please call our help line on the front page of this owner's manual.

SELECTING AUDIO/VIDEO INPUT

You can select external input jacks by pressing [GAME] on the remote control.

1 To use external input

2 To return to TV channel

 

 

GAME

15

 

 

 

 

 

 

GAME

 

 

GAME

 

 

 

 

 

 

 

Picture: GAME (ON)

Input: External

In the Game mode, you can use input jacks with suitable picture adjustments for video games.

Notes:

If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.

If you adjust another picture control while in Game mode, this mode will automatically be canceled.

MENU VOLUME OPERATIONSCHANNELREMOTE CONTROL AND FRONT PANEL FUNCTION POWER

MENU VOLUME INSTALLING THE BATTERIESCHANNELINITIAL SETUP POWER

Infrared Sensor Window

POWER button

To turn TV on/off

CHANNEL /buttons

To select channels

VOLUME X/Y buttons

To adjust volume

MENU button

To view on-screen menu

Note:

If some digits appear in the corner of the screen when the unit is turned on for the first time, press [POWER] without unplugging the power cord.

Page 2
Image 2
Symphonic WF206 Preparation For Use, Operations, Connections, Remote Control And Front Panel Function, Initial Setup