Tascam MD-301mkII Handling MDs, Memory back-up function, When Protected !! is displayed

ªHandling MDs

The MiniDisc (MD) measures 64 mm in diameter. Although the MD is housed in a protective cartridge (68 mm x 72 mm x 5 mm) and can be handled easily, deck malfunc- tions may result if the cartridge gets dust on it or is damaged. To protect the disc, always take the following precautions:

…Be sure that the MD is taken out of the deck and put back in its MD case after using it.

…Do not touch the disc inside the cartridge. Do not open the shutter to expose the MD.

…Do not place MDs in direct sunlight, high temperatures, or high levels of humidity.

…Use a dry, soft cloth to clean the cartridge.

…When attaching a label to the MD cartridge, be sure to apply it correctly to the specified position. If the label is rolled up or partially detached, the MD cartridge may get stuck inside the deck.

…Do not place one label on top of another.

Cartridge

Shutter

ªMemory back-up function

This unit is provided with a memory back-up function. When you use the deck for the first time, leave it on for about 5 minutes to allow the back-up circuit to be charged and become operational. When not using the deck for a while, try to turn the power on every 3 or 4 days.

ªSerial Copy Management System

This deck complies with the SCMS (Serial Copy Management System). As a result, it is not possible to digitally record from a source MD which has been recorded digitally.

ªWhen "Protected !!" is displayed

…A playback-only MD is loaded.

…The MD is record-protected against accidental erasure. To make recording (or editing) possible, slide the record- protect tab to close the hole.

ªWhile "UTOC Writing" is blinking:

"UTOC Writing" blinks while the MD is being ejected after recording (or editing). While it is blinking, the recorded data is being written on the MD. Do not pull out the power cord or vibrate the deck. Otherwise the recorded data may not be written correctly on the MD.

If the power is turned off with the MD left

in the deck (" " lights up) after recording, the UTOC cannot be recorded. Turn the power back on within 3 or 4 days and eject the MD. The recorded data might be lost if the MD is left in the deck for a long time.

ªWhen "D-IN UNLOCK !" blinks

…The program source is not connected to the [DIGITAL INPUT 1] or [DIGITAL IN 2] terminal even though you have selected [DIGITAL 1] or [DIGITAL 2] with the [INPUT SELECTOR]. Either make the digital connection or select [ANALOG] with the [INPUT SELECTOR] and perform analog recording.

…This message also appears when the digital signal input is interrupted during digital recording. To continue recording, restart the digital program source.

Remote Control Unit

When operating the remote control unit, point it towards the remote sensor on the front panel of the unit.

ªBattery installation

ENGLISH

1.Remove the battery compartment cover.

2.Insert two "AA" (R6, SUM-3) dry batteries.

Make sure that the batteries are inserted with their positive ± and negative — poles positioned correctly.

3.Close the cover until it clicks.

Battery replacement

If you notice that the distance between the remote control unit and the player for correct operation becomes shorter, it indicates that the batteries are exhaust- ed. In this case replace the batteries with new ones.

Precautions concerning batteries

…Be sure to insert the batteries with correct positive ± and negative — polarities.

…Use batteries of the same type. Never use different types of batteries together.

…Rechargeable and non-rechargeable batteries can be used. Refer to the precautions on their labels.

…When the remote control unit is not to be used for a long time (more than a month), remove the batteries from the remote control unit to prevent them from leaking. If they leak, wipe away the liquid inside the battery compartment and replace the batteries with new ones.

…Do not heat or disassemble batteries and never dispose of old batteries by throwing them in fire.

– 5 –