Technics SC-EH790, SC-EH590 Before recording Deck 2 only, Recording CDs, operations

A B

1

COUNTER

RESET DISPLAY DECK 1/2

6345 2

A

COUNTER

DISPLAY

COUNTER

RESET

C

	Side A
Tab for side B	Tab for side A
To re-record
Normal tape	High-position tape
A	A

Discrimination hole

D

operations		1
Recording			2	3	1
			<OPEN		Forward side
				Tape facing down
		2	DOLBY NR		ÎNR
					2
	RQT6866	3	REV MODE		ÎNR
					2

Before recording (Deck 2 only)

See page 39 for tape selection.

Note

[EH790]

You cannot record when [6CH DISCRETE INPUT] is selected.

Volume, sound quality and surround effects have no effect on recording. Sound quality and surround effects are automatically set to flat when recording.

ªA To display the tape counter while recording

Press [COUNTER DISPLAY].

The counter is displayed for about 5 seconds.

≥Press [COUNTER RESET] to reset the counter.

≥To display or reset the tape counter for deck 1, first press [DECK 1/2].

ªB Erasing recordings

1Press [INPUT SELECTOR] to select “TAPE”.

2 Insert the recorded tape into deck 2.

3 Press [DOLBY NR] so the “Î NR” indicator goes out. 4 Select the reverse mode.

5 Press [¥ REC PAUSE].

6 Press ["] or [!].

ªC Erasure prevention

The illustration shows how to remove the tabs to prevent recording. To record on the tape again, cover as shown, being careful not to cover the high position discrimination hole.

Your attention is drawn to the fact that recording pre-recorded tapes or discs or other published or broadcast material may infringe copy- right laws.

ªD Preparatory steps

Do these steps before each recording.

Wind up the leader tape so recording can begin immediately.

1 Press [< OPEN] on deck 2 and insert the cassette.

Close the holder by hand.

2 Press [DOLBY NR] to select Dolby NR on (“ÎNR” appears) or off.

(➡ “Dolby noise reduction”, page 19)

3 Press [REV MODE] to select the reverse mode.

Each time you press the button:

b:One side only records.

dand f: Both sides record (forward >reverse).

“f” automatically changes to “d” when [¥ REC PAUSE], [EDIT] or [TAPE EDIT] is pressed.

1 2

	∫
EH790	3
EDIT

DISC1–5∫

EH590 EDIT 3

∫

A

1

∫

2	¥REC	ÎNR
	PAUSE	2

REC

3

B
	EH790	EH590

EDIT

EDIT

2

REC

EDIT

Recording CDs

Preparation:

≥Do the preparatory steps (➡ page 28).

≥Insert the CD(s) you want to record (➡ page 8). ≥[EH790]

Press [DISC, 1–5] on the CD changer to select the disc where you want to start recording, then press [∫] to stop the disc.

ªA	Normal recording
1	Press ["] (reverse side) or [!] (forward side) then [∫] to
	set the tape direction.
2 Press [¥ REC PAUSE].
	The deck goes into the recording standby mode and the indicator “"”
	or “!” starts flashing.
3 Press [!] on the CD changer or CD player.
	Recording starts automatically.
4 seconds after the CD(s) finishes, the deck goes into the recording
standby mode.
To stop recording
EITHER
Press [∫] on the CD changer or CD player.
The deck goes into the recording standby mode 4 seconds later.
OR
Press [∫] on the deck.
Recording stops immediately but the CD continues to play.
To record programmed tracks
Program tracks before step 1 (➡ page 15).
ªB One touch CD editing
This function makes it easier for you to record from discs.
≥When recording, if a track is cut off in the middle at the end of the front
side, it is recorded from the beginning on the reverse side.
(Ensure the reverse mode “d” is selected. )
≥At the end of the reverse side recording stops and the current track will be
interrupted.
After pressing ["] or [!] then [∫] on the cassette deck to set the tape
direction,
Press [EDIT].
Recording starts. In the meantime, “CD EDIT” will scroll across the display.
After edit-recording has finished, the cassette deck automatically stops.
		operations
To edit programmed tracks
To stop editing
Press [∫] on the CD changer or CD player.
The cassette deck also stops. “EDIT OUT” scrolls across the display.		Recording
Program the tracks (➡ page 15) and press [EDIT].

RQT6866

29