Tefal BR304841, BR304849 Sgetting Started, Cleaning and Maintenance, Descaling your appliance

- Do not fill the tank with

hot water, milk or any

other liquid

- Make sure that no

foreign body such as

grit or small particles

gets into the water

tank: any damage

arising from foreign

bodies having entered

the tank is excluded

from the guarantee.

- Make sure that the

water is fresh so that it

has not had time to

become stagnant or in

contact with the air and

that it is odour free

- Never remove the tank

while the appliance is in

operation.

- If you use an entire

tank of water all at once

SGETTING STARTED

•Place the appliance on a flat, stable, heat resistant surface away from water splashes and any sources of heat.

1 – Put the appliance into the mains.

2 After having removed the lid B, remove and fill the tank A with cold water (fig. 1a and b).

3Put the tank back in place by pressingfirmly and repositionthe lid B (fig. 2).

4 Place the desired container under the nozzle E (fig. 8).

5 Press “continuous water supply” button H and you will instantly obtain hot water (fig. 3).

Keep it held down until you get the amount of hot water you want. Hot water will stop running as soon as you release the button.

6 You can also use the automatic setting button with a pre-set quantity for mugs. In this case, briefly press button G. The appliance will instantly provide the quantity needed to fill a mug and stop automatically. If you wish, stop the water before the end of the cycle, then again press the same automatic button G (fig. 8).

7 Models equipped with a quantity selector offer an additional function: you can adjust the amount of water automatically delivered to your container. To do this, select the chosen amount on the selector I, then press the auto- matic mug button G; the water flow will stop automatically (fig. 9).

8 If you use small cups, we advise you to bring the cup in close to tap E to avoid splashing.

					CLEANING AND MAINTENANCE
Do not immerse the		•	Systematically disconnect the power supply cord before any maintenance GB
appliance in water			operation. Then clean the appliance with a damp cloth.
Do not put the appliance
in the dishwasher
What to do if there is a PROBLEM
	Problems			Probable causes		Corrective actions
	Appliance makes a strange noise			No more water left in tank		Fill tank
				Tank is incorrectly fitted		Press the tank firmly to engage again
	Water flows too slowly or not at all			Not enough water in tank		Fill tank
				The tank is not fitted correctly		Press the tank firmly to engage again
				The appliance is coated with scale		Descale appliance
	Water is cold			The appliance is coated with scale		Descale appliance

(approximately

1.5 litres), let the

appliance rest for

10 minutes before

launching a new cycle

IF YOUR APPLIANCE IS DROPPED, HAS LEAKS OR IF THE POWER SUPPLY CORD OR PLUG ARE VISIBLY DAMAGED

Return your appliance to your authorised Service Centre. See the warranty conditions and the list of centres in the handbook provided with your appliance.

The type and series number are shown on the base of your model.

Do not use the appliance. No attempt must be made to disassemble the appliance or safety devices.

DESCALING your appliance

In order to optimise the lifetime of your appliance, we recommend that you descale it at least every 2 months. Descaling should be carried out more frequently if you live in a very hard water area.

To de-scale:

1 Remove the Claris filter cartridge (fig. 6).

2 Place a container with at least 1.5 litre under the spout.

3Empty the tank A if it is is still full of water, then reposition it on its base (fig. 2).

4 Pour 1 litre of commercially available white vinegar at 8° into the tank.

5 Press the continuous water supply button H and the mug pre-select button G simultaneously for at least 10 seconds (fig. 7).

6 The descaling cycle thus run automatically for approximately 10 minutes

7 When the cycle has come to an end, empty the container and refill the water tank to a maximum. Press the “continuous water supply” button H to relaunch a new operation for rinsing the appliance (fig. 3).

8 Once the last cycle has finished, reposition the Claris cartridge and your appliance will again be ready

(fig. 6).

Never use any other de-scaling method than that recommended.

This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.

IMPORTANT: SAFETY INSTRUCTIONS

•Carefully read the operating instructions before first use of the appliance and keep them in a safe place: Tefalshall not be held responsible for incorrect use.

•Only connect the appliance to an earthed socket. Check that the power supply voltage shown on the appliance’s rating plate corresponds to that of your installation

•Takecare not to place the appliance on a hot surface like a hot-plate or use it close to a naked flame.

•Immediately take the plug out from the mains if the appliance does not function correctly.

•Do not pull the power supply cable to remove the plug.

•Do not let the power supply cord hang down on the edge of a table or a work surface.

•Do not place your hand or the power supply cord on the hot parts of the appliance.

•Never soak the appliance, the cord or electrical plug in water or other liquid.

•Keep the appliance out of reach of children and certain disabled persons do not let the cord hang down.

•Do not use the appliance if the power supply cord or the appliance itself are damaged.

•To avoid any danger, do not use the appliance if the power supply cord or plug are damaged. It is compulsory to have the power supply cord replaced by a TEFAL authorised centre.

•Always refer to the instructions to de-scale the appliance.

12 13