Teka DHX T ISLA manual Accesories supplied, Installation, Active charcoal filters Optional

When exterior gas extraction is not possible, then the kitchen hood may be set to purify the air by recycling it through active charcoal

Fig. 1 (Page 43)

On installing the kitchen hood make sure that the Safety Instructions set out on page 10 are complied with.

To obtain optimum performance, the external conduct must not be more than FOUR METRES long, have no more than two 90° angles and its diameter must be at least Ø120.

	Accesories supplied	filters.
		The active charcoal filters have an active life of
1	150/ 120 mm reduction.	between three to six months, depending on
4	Screws (M4 x 12).	the individual conditions of use. These filters
		cannot be washed nor regenerated. They must
4	Screws (M4 x 10).
		be replaced once their useful life comes to an
6	Lock screws (Ø8 x 45).
		end.

Installation Fig. 1 (Page 43)

1) Mount the diffuser support (A13) onto the upper chassis (A6) with the screws (A4) (M4 x 12).

2) Adjust the diffuser (A5) over the support

(A13).

3) Connect the upper part of the inner tube (not supplied) to the circular support exit (A13).

4) Using the support (O) trace and drill the where the screw-fittings will sit onto the roof (S) (Ø8 x 45).

1)Using the support (O) trace and drill the 5) Screw the support (O) into the roof with the where the screw-fittings will sit onto the roof (S) screw-fittings (S) (Ø8 x 45).

(Ø8 x 45).	6) Mount the upper chassis	(A6) onto the
2) Screw the support (O) into the roof with the
	support (O) using the screws (Q) (M6 x 16).
screw-fittings (S) (Ø8 x 45).	7) Mount the upper cover (A8) and attach it to
3) Mount the upper chassis (A6) onto the
	the upper chassis (A6) with the screws (G) (M4
support (O) using the screws (Q) (M6 x 16).	x 12).
4) Connect the upper part of the inner tube (not
	8) Mount the whole lower unit (A7) to the upper
supplied) to the exit.	section, attaching it to the	roof using the

5)Mount the upper cover (A8) and attach it to screws (A10) (M4 x 12) at the required height. the upper chassis (A6) with the screws (G) (M4 9) Fasten the inner tube (not supplied) with a

x 12).clamp to the air-outlet of the motor.

6) Fit the part (B) if the inner tube (not supplied) 10) Mount the lower part (A9a) of the cover to is Ø120.

the lower chassis (A7) with the screws (I)

7) Mount the whole lower unit to the upper (M4x12).

section, attaching it to the roof using the 11) Adjust the lower part (A9b) of the cover screws (A10) (M4 x 12) at the required height. (A9a) as shown in the diagrams.

8)Attach the inner tube with a clamp (not 12) Remove the metal filters. Loosen the supplied) to (B) or on to the motor's air outlet screws of the EASYCLEAN panels (A19) and

vent as the case may be.. take them off.

9)Mount the lower part (A9a) of the cover to 13) Fit the nut-supports (F) onto the body of the the lower chassis (A7) with the screws (I) (M4 kitchen hood.

x 12).		14) Attach the supports (B) with the screws (E)
10) Adjust the lower part (A9b) of the cover		(M4 x 12) onto the nuts (F).
(A9a) as shown in the diagrams.		15) Mount the carbon filters (A) introducing the
		anchorages into the grooves of the supports
	Active charcoal filters (Optional)	(B).
		16) Fit the metal filters.

ENG

13