Tekkeon ET1000 manual U S E R G U I D E, Charging EZTALKER, Unpacking EZTALKER, Getting Started

ET1000

EZTALKER by Tekkeon is a sleek cord-free headset that enables comfortable handsfree communication with your mobile phone. EZTALKER 1000 works with your Bluetooth-ready mobile phone to provide clear, high-quality communication.

U S E R G U I D E

Charging EZTALKER

Before using ezTalker, you must charge the headset for approximately two hours. When fully charged, the battery provides up to four hours of talk time and up to 168 hours of standby time.

While using your EZTALKER headset, you can store your mobile phone in your pocket, backpack, or briefcasejust about anywhere in close proximity that is convenient for you.

Unpacking EZTALKER
Your ezTalker package includes
the following:
! ezTalker Headset	!
∀ Charging cradle with belt clip
	∀
# Charger

To Charge the Headset

1.Insert ezTalker into the charging cradle as shown.

2.Plug the charger into the charging jack on the right side of the charging cradle.

3.Plug the charger into a wall outlet. While the headset is charging, the amber LED on the headset will remain on. When the headset is fully charged, the amber LED will turn off.

Figure 1.

ezTalker inserted into

charging cradle

% ezEarhook	#	%
& ezFit Ring

∋Comfort Pad

( User guide (not shown) & ∋

Getting to Know EZTALKER

TALK Button

Used for turning headset on/off, pairing, and making/receiving calls

Amber and Blue LEDs

Provides visual indication of headset status: power on/off, pairing mode, muting mode, charging mode, and low battery

Volume Control

Used to adjust the speaker volume and to mute the microphone

Microphone

Speaker

Getting Started

Before using ezTalker, you must:

)Charge ezTalker

)Pair ezTalker to your mobile phone

)Fit ezTalker to your ear

)Power ezTalker

Directions for each of these activities are provided in the following four sections. Once these steps are completed, you will be ready to use ezTalker!

4.Unplug the charger cable from the wall outlet and the charging cradle.

BATTERY INDICATION: When the battery is low (less than 10% of capacity), the amber LED will flash and you’ll hear a double beep every 32 seconds.

Pairing EZTALKER to Your Mobile Phone

Pairing is the process of linking the headset with your Bluetooth mobile phone. Before using ezTalker with your mobile phone you must pair the devices. After this process is complete, you can use the headset only with its paired mobile phone. To use ezTalker with a different mobile phone, you must repeat the pairing process with the new mobile phone. In this case, the headset will no longer work with the original mobile phone.

BEFORE YOU PAIR THE HEADSET, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET.

To Pair the Devices

1.Turn on the mobile phone and place it within 10 feet of the headset.

2.Initiate the Bluetooth device-pairing (discovery) feature on the mobile phone. Refer to the mobile phone user guide for instructions on initiating this feature.

3.With the headset turned off, press and hold the TALK button approximately five seconds, until the blue and amber LEDs flash alternately or until you hear the PAIRING tone.

4.Release the TALK button. The headset is now in Pairing Mode.

5.Follow the mobile phone prompts, and when prompted for the passkey (also called passcode or BT PIN), enter 0000 (the ezTalker passkey). When pairing is complete, the headset will be placed in Standby Mode, ready to make and receive calls, the amber LED will turn off, and the blue LED will flash at two-second intervals.

1