Tektronix 071-1631-04, AFG3000 Series Inputs/Outputs

Specifications

88 AFG3000 Series Quick Start User Manual

Inputs/Outputs

Front Panel

CH1 Trigger Output

Level Positive TTL level pulse into 1 kΩ

Impedance 50 Ω

Jitter (rms), typical 500 ps (AFG3011, AFG3021B/AFG3022B)

200 ps (AFG3101/AFG3102)

100 ps (AFG3251/AFG3252)

Trigger Input

Level TTL compatible

Pulse Width 100 ns minimum

Impedance 10 kΩ

Slope Positive/Negative, selectable

Trigger Delay 0.0 ns to 85.000 s

Resolution: 100 ps or 5 digits

Jitter (rms), typical Burst: <500 ps (Trigger input to signal output)

Rear Panel

External Modulation Input

Input Range ±1.0 V full scale (except FSK)

3.3 V logic level (FSK)

Impedance 10 kΩ

Frequency Range AM, FM, PM, FSK, PWM: DC to 25 kHz (122 KS/s)

External Reference Output (AFG3011, AFG3101/AFG3102 and AFG3251/AFG3252)

Impedance 50 Ω, AC coupled

Amplitude 1.2 Vp-p into 50 Ω

External Reference Input

Impedance 1 kΩ, AC coupled

Required Input Voltage Swing 100 mVp-p to 5 Vp-p

Lock Range 10 MHz ±35 kHz

CH1 Additional Input (AFG3101/AFG3102 and AFG3251/AFG3252)

Impedance 50 Ω

Input Range –1 V to +1 V (DC + peak AC)

Bandwidth DC to 10 MHz (–3 dB) at 1 Vp-p

Contents

Main Contacting Tektronix Warranty 16 Page Table of Contents ii General Safety Summary To avoid Fire or Personal Injury Symbols and Terms Environmental Considerations Product End-of-Life Handling Equipment Recyc ling. Mercury Notification. Restriction of Hazardous Substances Page Preface ? Documentation viii Conventions Used in this Manual Quick Tutorial 2 To Generate a Sine Waveform Page 4 Accessing Help Getting Started General Features 6 Before Installation Operating Requirements Power Supply Requirements Environmental Standard Accessories 8 Recommended Accessories Powering the Instrument On and Off Power Off Power On To Change Instrument Settings at Power-on 10 Self Test and Self Calibration Selecting a Local Language 12 Protect Your Instrument from Misuse Check Input and Output Connectors Do not mistake Output connectors for Input. Use Fuse Adapter Output Input Floating Ground 14 Protect Your DUT Update Your Instrument Firmware 16 Page 18 Connect to a Network USB Interface Ethernet Setup Page 20 Equivalent Output Circuits 22 Overheat Protection (AFG3011 Only) Getting Acquainted with Your Instrument AFG3000 Series Quick Start User Manual 23 Getting Acquainted with Your Instrument To unlock the front panel without using a remote command, push the front-panel Cancel button twice. Front Panel Overview To Lock or unlock the Front Panel Controls If you need to lock the front panel controls, use the following remote command: Screen Interface Bezel Menu. Main Displa y Area and View T ab. Output Status. Message Displa y Area. Level Meter . View Button 26 Shortcut Buttons Default Setup 28 Select Waveform Page Select Run Mode Adjust Waveform Parameters 32 Channel Select (dual-channel model only) Output ON/OFF Rear Panel Operating Basics Generate a Pulse Waveform 36 Save/Recall Arbitrary Waveforms Generate an Arbitrary Waveform 38 Modify an Arbitrary Waveform (Edit Menu) Arbitrary Waveform Edit Example 1 40 Arbitrary Waveform Edit Example 2 Generate Noise/DC 42 Generate a Burst Waveform T riggered Burst Mode. Gated Burst Mod e . To Generate a Triggered Burst Waveform To Generate a Gated Burst Waveform 44 Sweep a Waveform Page Modulate a Waveform Page 48 To Output an FSK Waveform Page 50 Trigger Out Page 52 Adjusting Parameters of Two Channel Signals (dual-channel model only) Phase Page 54 Set up Load Impedance Invert Waveform Polarity 56 Add Noise Add Signal (AFG3100 and AFG3200 Series) 58 Generating a Differential Signal External Reference Clock (Except AFG3021B and AFG3022B) 60 Synchronous Operation (Except AFG3021B and AFG3022B) Page 62 USB Memory Utility Menu Page Save/Recall Instrument Setup Saving a Screen Image Using the Security Menu Access Protection 68 Changing the Password ArbExpress Screen Interface Page Page Page Page Application Examples Lissajous Patterns 76 Measurement of Filter Characteristics Motor Speed Control by Pulse-Width Modulation 78 Carrier Null (Frequency Modulation) Specifications Electrical (except AFG3011) 80 Page 82 Page 84 Electrical (AFG3011) Page 86 Page 88 Inputs/Outputs General 90 EC Declaration of Conformity EMC EN 61326:1997. EN 61000-3-2:2000. EN 61000-3-3:1995. Eur opean Conta ct. Australia/New Zealand Declaration of Conformity EMC Specifications Instrument Dimensions Dimensions of the RM3100 Rackmount Page Index A B C D M N O P Q V W