Tektronix 1502C - page 105

Appendix C: Operator Troubleshooting

1502C MTDR User Manual C–5

At power on during initialization only.

The instrument changed the gain while adjusting the pulse to be two divisions

high and the change in the gain circuitry did not make the expected change in the

signal size.

Have the instrument repaired. If no other error messages occurred and the pulse

is present, distance measurements can be made. Do not make loss measurements

until the instrument has been repaired.

ERROR: Acquisition Initialization

TYPE: Vertical Position failure

Pulse base off top of LCD

ERROR: Acquisition Initialization

TYPE: Vertical Position failure

Pulse top below base of LCD

ERROR: Acquisition Initialization

TYPE: Vertical Position failure

At power on during initialization only.

The instrument attempts to center the pulse before making it two divisions high.

These messages indicate that the waveform could not be properly placed on the

display. This usually means that the offset or gain circuitry on the Main board is

not working properly.

The instrument must be repaired. If it is possible to adjust the pulse vertically on

the display and no other error messages have been displayed, it might be possible

to make measurements. If the pulse is not two divisions high, do not make

measurements.

ERROR: Acquisition Initialization

TYPE: Leading edge of pulse not found

ERROR: Acquisition Initialization

TYPE: Top of 50 nsec ramp not found

This message can occur at power on initialization only. These are common error

messages because they are triggered by many kinds of failures and come from

one of the very first routines that the instrument executes. They are usually fatal

Occurrences:

Meanings:

Remedies:

Message:

Occurrences:

Meanings:

Remedies:

Message:

Occurrences:

Contents

Main Page WARRANTY Contacting Tektronix Table of Contents Page List of Figures Page Page Page General Information Installation and Repacking Unpacking and Initial Inspection Repacking for Shipment Power Source and Power Requirements Page Page General Safety Summary Safety Terms and Symbols Page Page Page Operating Instructions Overview Powering the 1502C Handling Care of the Battery Pack Battery Charging Low Battery Low Temperature Operation Preparing to Use the 1502C 1502C Tektronix Operating Instructions 161502C MTDR User Manual Display Figure 14: Display and Indicators Front-Panel Controls Menu Selections Main Menu Page Page Page Test Preparations The Importance of Vp (Velocity of Propagation) Finding an Unknown Vp Operating Instructions 1502C MTDR User Manual 113 Figure 17: Vp Set at .66, Cursor at Reflected Pulse (Set Correctly) Figure 15: Vp Set at .30, Cursor Beyond Reflected Pulse (Set Too Low) Figure 16: Vp Set at .99, Cursor Less Than Reflected Pulse (Set Too High) Cable Test Procedure Distance to the Fault Page Page Reflection Coefficient Measurements Return Loss Measurements Ohms-at-Cursor Using VIEW INPUT How to Store the Waveform Using VIEW STORE Using VIEW DIFF Page Page Using Horizontal Set Reference Page Using Vertical Set Reference Vertical Compensation for Higher Impedance Cable Page Page Additional Features (Menu Selected) Max Hold Pulse On/Off Single Sweep Page Operator Tutorial What is the Tektronix 1502C? How Does It Do It? You, the Operator Menus and Help Getting Started Page Page The Waveform Up Close Page A Longer Cable Ohms-at-Cursor Page Page Noise Page Set Ref (Delta Mode) HORZ SET REF Page VERT SET REF Page VIEW INPUT STORE and VIEW STORE Page VIEW DIFF Menu-Accessed Functions Max Hold Page Pulse On / Off Single Sweep Page TDR Questions and Answers Page Page Options and Accessories Option 04: YT-1 Chart Recorder Option 05: Metric Default Option 07: YT-1S Chart Recorder Power Cord Options Test Data Record Option Option DE Optional Accessories Accessories Standard Accessories Options and Accessories 1502C MTDR User Manual 33 Page Appendix A: Specifications Electrical Characteristics A21502C MTDR User Manual Table A1: Electrical Characteristics (Cont.) 1502C MTDR User Manual A3 Environmental Characteristics Table A2: Environmental Characteristics A41502C MTDR User Manual Certifications and Compliances (continued next page) 1502C MTDR User Manual A5 Physical Characteristics Table A3: Physical Characteristics Page Appendix B: Operator Performance Checks Equipment Required Getting Ready Power On Metric Instruments Set Up 1. Horizontal Scale (Timebase) Check Page Page 2. Vertical Position (Offset) Check 3. Noise Check 4. Offset/Gain Check 5. Sampling Efficiency Check 6. Aberrations Check 7. Risetime Check Page 8. Jitter Check Conclusions Appendix C: Operator Troubleshooting Appendix C: Operator Troubleshooting C21502C MTDR User Manual Operator Troubleshooting (with cases on) Error Messages Message: Occurrences: Meanings: Message: Remedies: Page Page Page Appendix D: Application Note Pulse Echo Testing of Electrical Transmission Lines Using the Tektronix Time-Domain Reflectometry Slide Rule Terms and Symbols Relationships VSWR vs. Percent Reflected Voltage Return Loss (dB) vs. Percent Reflected Voltage Appendix D: Application Note D41502C MTDR User Manual Percent Reflected Voltage vs. Characteristic Line Impedance Figure D3: Slide Rule 50 ohm Source +1r = W+.03r = 53.1W Appendix D: Application Note 1502C MTDR User Manual D5 Percent Reflected Voltage vs. Load Resistance Characteristic Line Impedance or Load Resistance vs. Reflection Amplitude (as seen on your TDR) Centimeters vs. Inches or Meters vs. Feet Dielectric Constant vs. Velocity Factor Time vs. Short Distances, in Centimeters or Inches Time vs. Long Distances, in Meters or Feet Page Glossary Page Page Page Page Page 1502C MTDR User Manual Index1 Index A B C D I L M N O Q R S T U