Tektronix 1502C Single Sweep

Operating Instructions

1502C MTDR User Manual 1–31

6. Repeatedly press MENU until the instrument returns to normal operation.

CAUTION. This function is used mostly for troubleshooting by qualified techni-

cians. It is not recommended that you use the 1502C as a stand-alone monitor-

ing device. The input circuitry is very sensitive and can be easily damaged by

even moderate level signals.

NOTE. In this mode, the 1502C is acting as a detector only. Any pulses detected

will not originate from the instrument, so any distance readings will be invalid.

If you are listening to a local area network, for example, it is possible to detect

traffic, but not possible to measure the distance to its origin.

Pulse is: Off can be used in conjunction with Max Hold is: On.

7. To exit Pulse is: Off, access the Acquisition Control Menu again, turn the

pulse back on, then repeatedly push MENU until the instrument returns to

normal operation.

The single sweep function will acquire one waveform only and display it.

1. Attach a cable to the 1502C front-panel CABLE connector.

2. Push MENU to access the Main Menu.

3. Scroll to Setup Menu and push MENU again.

4. Scroll to Acquisition Control Menu and push MENU again.

5. Scroll to Single Sweep is: Off and push MENU again. This will change to

Single Sweep is: On.

6. Repeatedly press MENU until the instrument returns to normal operation.

7. When you are ready to begin a sweep, push VIEW INPUT. A sweep will

also be initiated when you change any of the front-panel controls. This

allows you to observe front panel changes without exiting the Single Sweep

mode.

As in normal operation, averaged waveforms will take longer to acquire.

Single Sweep

Contents

Main Page WARRANTY Contacting Tektronix Table of Contents Page List of Figures Page Page Page General Information Installation and Repacking Unpacking and Initial Inspection Repacking for Shipment Power Source and Power Requirements Page Page General Safety Summary Safety Terms and Symbols Page Page Page Operating Instructions Overview Powering the 1502C Handling Care of the Battery Pack Battery Charging Low Battery Low Temperature Operation Preparing to Use the 1502C 1502C Tektronix Operating Instructions 161502C MTDR User Manual Display Figure 14: Display and Indicators Front-Panel Controls Menu Selections Main Menu Page Page Page Test Preparations The Importance of Vp (Velocity of Propagation) Finding an Unknown Vp Operating Instructions 1502C MTDR User Manual 113 Figure 17: Vp Set at .66, Cursor at Reflected Pulse (Set Correctly) Figure 15: Vp Set at .30, Cursor Beyond Reflected Pulse (Set Too Low) Figure 16: Vp Set at .99, Cursor Less Than Reflected Pulse (Set Too High) Cable Test Procedure Distance to the Fault Page Page Reflection Coefficient Measurements Return Loss Measurements Ohms-at-Cursor Using VIEW INPUT How to Store the Waveform Using VIEW STORE Using VIEW DIFF Page Page Using Horizontal Set Reference Page Using Vertical Set Reference Vertical Compensation for Higher Impedance Cable Page Page Additional Features (Menu Selected) Max Hold Pulse On/Off Single Sweep Page Operator Tutorial What is the Tektronix 1502C? How Does It Do It? You, the Operator Menus and Help Getting Started Page Page The Waveform Up Close Page A Longer Cable Ohms-at-Cursor Page Page Noise Page Set Ref (Delta Mode) HORZ SET REF Page VERT SET REF Page VIEW INPUT STORE and VIEW STORE Page VIEW DIFF Menu-Accessed Functions Max Hold Page Pulse On / Off Single Sweep Page TDR Questions and Answers Page Page Options and Accessories Option 04: YT-1 Chart Recorder Option 05: Metric Default Option 07: YT-1S Chart Recorder Power Cord Options Test Data Record Option Option DE Optional Accessories Accessories Standard Accessories Options and Accessories 1502C MTDR User Manual 33 Page Appendix A: Specifications Electrical Characteristics A21502C MTDR User Manual Table A1: Electrical Characteristics (Cont.) 1502C MTDR User Manual A3 Environmental Characteristics Table A2: Environmental Characteristics A41502C MTDR User Manual Certifications and Compliances (continued next page) 1502C MTDR User Manual A5 Physical Characteristics Table A3: Physical Characteristics Page Appendix B: Operator Performance Checks Equipment Required Getting Ready Power On Metric Instruments Set Up 1. Horizontal Scale (Timebase) Check Page Page 2. Vertical Position (Offset) Check 3. Noise Check 4. Offset/Gain Check 5. Sampling Efficiency Check 6. Aberrations Check 7. Risetime Check Page 8. Jitter Check Conclusions Appendix C: Operator Troubleshooting Appendix C: Operator Troubleshooting C21502C MTDR User Manual Operator Troubleshooting (with cases on) Error Messages Message: Occurrences: Meanings: Message: Remedies: Page Page Page Appendix D: Application Note Pulse Echo Testing of Electrical Transmission Lines Using the Tektronix Time-Domain Reflectometry Slide Rule Terms and Symbols Relationships VSWR vs. Percent Reflected Voltage Return Loss (dB) vs. Percent Reflected Voltage Appendix D: Application Note D41502C MTDR User Manual Percent Reflected Voltage vs. Characteristic Line Impedance Figure D3: Slide Rule 50 ohm Source +1r = W+.03r = 53.1W Appendix D: Application Note 1502C MTDR User Manual D5 Percent Reflected Voltage vs. Load Resistance Characteristic Line Impedance or Load Resistance vs. Reflection Amplitude (as seen on your TDR) Centimeters vs. Inches or Meters vs. Feet Dielectric Constant vs. Velocity Factor Time vs. Short Distances, in Centimeters or Inches Time vs. Long Distances, in Meters or Feet Page Glossary Page Page Page Page Page 1502C MTDR User Manual Index1 Index A B C D I L M N O Q R S T U