Teledyne 3010MB Installation

Percent Paramagnetic Oxygen Analyzer Part I: Control Unit

Part I: 3-1

Teledyne Analytical Instruments

Installation

Installation of Model 3010MB Analyzers includes:

1. Unpacking, mounting, and interconnecting the Control Unit and

the Analysis Unit

2. Making gas connections to the system

3. Making electrical connections to the system

4. Testing the system.

This chapter covers installation of the Control Unit. (Installation of the

Analysis Unit is covered in Part II of this manual.)

3.1 Unpacking the Control Unit

The analyzer is shipped with all the materials you need to install and

prepare the system for operation. Carefully unpack the Control Unit and

inspect it for damage. Immediately report any damage to the shipping agent.

3.2 Mounting the Control Unit

The Model 3010MB Control Unit is for indoor/outdoor use in a general

purpose area. This Unit is NOT for any type of hazardous environments.

The standard model is designed for indoor/outdoor mounting. Figure 3-

1 is an illustration of a Model 3010MB standard Control Unit front panel

and mounting brackets located-two at the top and two at the bottom of the

units frame.

Contents

Main i Percent Paramagnetic Oxygen Analyzer Model 3010MB Percent Paramagnetic Oxygen Analyzer Bulkhead Mount Control Unit, PN D-71385 Bulkhead Mount Analysis Unit, PN D-71394 DANGER P/N xxxxxx 12/21/99 ECO: #99-0000 ii Model 3010MB Copyright 1999 Teledyne Analytical Instruments Page iv Specific Model Information v Preface Overview Typical Applications vi Main Features of the Analyzer Model 3010MB Oxygen Analyzer Part I: Control Unit ii: Part I Part I: iii Alarms Range Page Introduction 1.1 Overview 1.2 Control Unit Inner Control Panel 3010MB Series 1.3 Recognizing Difference Between LCD & VFD Page Page Page Part I: 2-1 Operational Theory 2.1 Introduction 2.2 Electronics and Signal Processing 2-2: Part I 2 Operational Theory Model 3010MB Figure 2-1: Block Diagram of the 3010TB CU Electronics Self Test Signal Part I: 3-1 Installation 3.1 Unpacking the Control Unit 3.2 Mounting the Control Unit 3-2: Part I Part I: 3-3 3.3 Electrical Connections 3-4: Part I Primary Input Power: Fuse Installation: Analog Outputs: Part I: 3-5 3-6: Part I Part I: 3-7 3-8: Part I Part I: 3-9 Table 3-3: RS-232 Signals 3-10: Part I Part I: 3-11 3-12: Part I 3.4 Testing the System Part I: 4-1 Operation 4.1 Introduction 4-2: Part I 4.2 Using the Data Entry and Function Buttons Range. Alarms. Span. System 4.3 The Function 4-4: Part I Part I: 4-5 4-6: Part I Part I: 4-7 4-8: Part I Part I: 4-9 4-10: Part I Zero Span and Part I: 4-11 4.4 The 4-12: Part I Part I: 4-13 4-14: Part I Part I: 4-15 4-16: Part I 4.4.3 Span Failure Alarms 4.5 The Function Part I: 4-17 4-18: Part I Alarms Range 4.6 The Function Part I: 4-19 Range Analyze 4-20: Part I 4.7 The Function Part I: 4-21 4.8 Signal Output 4 Operation Model 3010MB 4-22: Part I Part I: 5-1 Maintenance WARNING: SEE WARNINGS ON THE TITLE PAGE OF THIS MANUAL. 5.1 Fuse Replacement 5-2: Part I 5.2 System Self Diagnostic Test Part I: 5-3 5.3 Major Internal Components 5-4: Part I Model 3010M Oxygen Analyzer Part II: Analysis Unit ii: Part II Part II: 1-1 Operational Theory 1.1 Introduction 1.2 Precise Paramagnetic Sensor 1-2: Part II Part II: 1-3 1.3 Cross Interference Sensor (rear view shown) 1-4: Part II 1 Operational Theory Model 3010M Teledyne Analytical Instruments Maintenance Page Appendix A-1 Specifications Page A-2 Recommended 2-Year Spare Parts List A-3 Drawing List