Texas Instruments 570CD 2.5.4

2.5.4 Installing External SVGA Monitor

The notebook is capable of driving both its internal LCD di splay and an

external SVGA monitor (LCD only, simultaneous, or SVGA only). The

external monitor connector pinouts and co nnector locations are shown in

Figure 2-5. To install an external monitor with the notebook, use the

following steps:

1. Ensure that both the note book and the external monitor are turned

off.

2. Locate the 15-pin female SVGA port on the Port Adapter.

3. Attach the appropriate end of the monitor cable to the SVGA port on

your notebook. If the monitor cable connectors have retaining screws,

tighten them down.

4. If necessary, connect the monitor power cable to the monitor, and

plug the monitor power cable into an electrical outlet.

5. Power on the monitor, as well as any other peripheral devices

connected to the notebook; then power up the notebook.

1

2

3

4

5

6

7

8

9

10

11, 12

13

14

15

RED VIDEO

GREEN VIDEO

BLUE VIDEO

NOT USED

GROUND

RED RETURN

GREEN RETURN

BLUE RETURN

NOT USED

GROUND

NOT USED

HORIZONTAL SYNC

VERTICAL SYNC

NOT USED

OUTPUT

OUTPUT

OUTPUT

INPUT

INPUT

INPUT

OUTPUT

OUTPUT

PIN

SIGNAL NAME

DIRECTION

EXTERNAL VGA CONNECTOR PI N OUTS

1

2

3

4

5

7

8

9

10

6

1112

13

14

15

Figure 2-5 Connecting an External SVGA Monitor

2-8 Installation

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service A Self Test Error Messages B PC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Features Model 570CD Model 570CDT Model 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page 1.4.1 1.4.2 1.4.3 Glidepad Select Buttons n 1.4.3.1 Controls and Indicators n 1.4.4 ^ 1.4.5 n 1.4.6 1.4.7 1.5 1.6 1.6.1 1.6.2 1.7 Specifications Page Specifications Models 570CD/575CD Models 570CDT/575CDT 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 2.3.2 2.3.3 2.4 c 2.5 2.5.1 Page 2.5.2 2-6 Installation Figure 2-3 Parallel Port Location/Pinouts 2.5.3 c 2.5.4 2.5.5 2.6 c AC Adapter 2.7 AC Power (120VAC to 230 VAC, 50 to 60 Hz) 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 3.3 3.3.1 Page 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 Page 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD 4-2 Theory of Operation System Controller 82C557 Figure 4-1 Notebook Functional Block Diagram Address Range Device Controller Channel Address Function Priority Interrupt Number Interrupt Source n 4.2.2 4.2.3 4.2.4 c 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 Page 4.2.9.4 DC-DC Converter/Battery Charger Circuit 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart See Appendix B (PC-Doctor) 5-2 Troubleshooting Procedures 5.3 5.3.1 recharged battery pack if battery is discharged) 5-4 Troubleshooting Procedures Figure 5-2 Troubleshooting Block Diagram n 5.3.3 5.3.4 5.3.5 Page Interactive Tests Supporting Online documentation Page 5.3.5.3 Running PC-Doctor n 5.3.5.4 Quitting PC-Doctor n 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Page Item No. 6.5 c Procedures n 6.5.1 Pack 6.5.3 6.5.4 Modules (DIMMs) 6.5.5 6.5.6 6.5.7 Assembly 6.5.8 6.5.9 6.5.10 6.5.11 n 6.5.12 6.5.13 6.5.14 6.5.15 c Appendix A Self Test Error Messages A.1 Error Messages A-1 Table A-1 Self Test Error Messages Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Checkpoint No. Description Error Messages A-3 Checkpoint No. Description A-4 Error Messages Page B PC-Doctor Diagnostics B.1 PC-Doctor Diagnostics B-1 B.2 B.3 Table B-1 PC-Doctor Key Assignments B-2 PC-Doctor Diagnostics Table B-2 Test Selection Menu Special Keys B.4 n B.5.1 B.5.2 B.5.3 B.5.4 B.5.5 B.6 B-6 PC-Doctor Diagnostics B.7