Texas Instruments 570CD 6.5.14

4. Lift up on the front edge of the main board until it clears the battery

cavity; then pull the main board forward and out of the plastics.

5. Reassembly is the reverse of steps 1 through 4 above.

6.5.14 Removing/Replacing HDD Connector Board

To remove and replace the HDD connector board Assembly, per form the

following procedure:

1. Remove the top case assembly as described in Paragraph 6.5.8.

2. Remove the main board assembly as described in Paragraph 6.5.13.

3. Turn the main board over and lay on a flat surface.

4. Using a small Phillips screwdriver, remove the two screws securing

the HDD connector board to the main board.

5. Replacement is the reverse of Steps 1 through 4.

New P/S

Board

Remove all other board

assemblies; then remove four

Hex Standoffs and four screws.

Main Board

Assembly

Figure 6-4 Replacing the Main Board Assembly

6-14 Field Service

Contents

Main Page Contents Preface 1 General Description 2 Installation 3 Operating Instructions 4 Theory of Operation 5 Troubleshooting Procedures 6 Field Service A Self Test Error Messages B PC-Doctor Diagnostics Preface Introduction Intended Audience Contents Other Manuals About the System Ordering Parts and Supplies 1 General Description 1.1 1.2 Features Model 570CD Model 570CDT Model 1.3 Configuration P/N Suffix Configuration P/N Suffix 1.4 Page 1.4.1 1.4.2 1.4.3 Glidepad Select Buttons n 1.4.3.1 Controls and Indicators n 1.4.4 ^ 1.4.5 n 1.4.6 1.4.7 1.5 1.6 1.6.1 1.6.2 1.7 Specifications Page Specifications Models 570CD/575CD Models 570CDT/575CDT 1.8 2 Installation 2.1 2.2 n 2.3 c n 2.3.1 2.3.2 2.3.3 2.4 c 2.5 2.5.1 Page 2.5.2 2-6 Installation Figure 2-3 Parallel Port Location/Pinouts 2.5.3 c 2.5.4 2.5.5 2.6 c AC Adapter 2.7 AC Power (120VAC to 230 VAC, 50 to 60 Hz) 2.8 2.9 2.10 3 Operating Instructions n 3.1 3.2 3.2.1 3.2.2 3.3 3.3.1 Page 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 Page 4 Theory of Operation 4.1 4.2 4.2.1 MAIN BOARD 4-2 Theory of Operation System Controller 82C557 Figure 4-1 Notebook Functional Block Diagram Address Range Device Controller Channel Address Function Priority Interrupt Number Interrupt Source n 4.2.2 4.2.3 4.2.4 c 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 Page 4.2.9.4 DC-DC Converter/Battery Charger Circuit 5 Troubleshooting Procedures 5.1 5.2 SEE PARAGRAPH 5.3.3 Figure 5-1 Troubleshooting Flowchart See Appendix B (PC-Doctor) 5-2 Troubleshooting Procedures 5.3 5.3.1 recharged battery pack if battery is discharged) 5-4 Troubleshooting Procedures Figure 5-2 Troubleshooting Block Diagram n 5.3.3 5.3.4 5.3.5 Page Interactive Tests Supporting Online documentation Page 5.3.5.3 Running PC-Doctor n 5.3.5.4 Quitting PC-Doctor n 6 Field Service c 6.1 6.2 6.2.1 c 6.2.2 6.2.3 6.2.4 6.3 c 6.4 and Assemblies 6.4.1 Page 6.4.2 Page Item No. 6.5 c Procedures n 6.5.1 Pack 6.5.3 6.5.4 Modules (DIMMs) 6.5.5 6.5.6 6.5.7 Assembly 6.5.8 6.5.9 6.5.10 6.5.11 n 6.5.12 6.5.13 6.5.14 6.5.15 c Appendix A Self Test Error Messages A.1 Error Messages A-1 Table A-1 Self Test Error Messages Error Message Corrective Action Table A-2 POST Checkpoint List A-2 Error Messages Checkpoint No. Description Error Messages A-3 Checkpoint No. Description A-4 Error Messages Page B PC-Doctor Diagnostics B.1 PC-Doctor Diagnostics B-1 B.2 B.3 Table B-1 PC-Doctor Key Assignments B-2 PC-Doctor Diagnostics Table B-2 Test Selection Menu Special Keys B.4 n B.5.1 B.5.2 B.5.3 B.5.4 B.5.5 B.6 B-6 PC-Doctor Diagnostics B.7