Manuals / Texas Instruments / Computer Equipment / Switch

Texas Instruments HPL-D SLLU064A manual Bill of Materials, EVM Construction

Models: HPL-D SLLU064A

1 27

Download 27 pages 55.11 Kb

Page 27

3 EVM Construction

3.4 Bill of Materials

Table 3-2. Bill of Materials for SN65LVDS125A / SN65LVDS250 EVM

	Item	6456526-1	6456526-2	6456526-3	Description	Pattern	Reference
		Qty	Qty	Qty			Designator
	1	9	9	9	0.001 µF	402	C2, C3, C4, C5, C6,
							C7, C8, C9, C10
	2	2	2	2	0.01 µF	603	C13, C18
	3	1	1	1	0.1 µF	603	C21
	4	2	2	2	0.1 µF	1206	C14, C19
	5	4	4	4	100 Ω (uninstalled)	402	R5, R8, R11, R14
	6	2	2	2	10 µF	7343	C11, C16
	7	1	1	1	1 µF	603	C22
	8	2	2	2	1 µF	1206	C15, C20
	9	12	12	12	3 pos jumper		W1, W2, W3, W4,
	9	12	12	12	3 pos jumper		W5, W6, W7, W8,
							W9, W10, W11, W12
	10	8	8	8	49.9 Ω (uninstalled)	402	R6, R7, R9, R10,
							R12, R13, R15, R16
	11	8	8	8	49.9 Ω	402	R1, R2, R3, R4, R17,
							R18, R19, R20
	12	2	2	2	68 µF	Cap 592D R	C12, C17
	13	4	4	4	Banana jack		J17, J18, J19, J20
						SMA END	J1, J2, J3, J4, J5, J6,
	14	16	16	16	SMA PCB MT MOD	50 Ω	J7, J8, J9, J10, J11,
	14	16	16	16	SMA PCB MT MOD		J12, J13, J14, J15,
							J12, J13, J14, J15,
							J16
	15	1	0	0	SN65LVDS125A	38-TSSOP	U1
						(DBT)
	16	0	1	0	SN65LVDS250	38-TSSOP	U1
						(DBT)
	17	0	0	1	Special	38-TSSOP	U1
						(DBT)
	18	4	4	4	Rubber feet	3/8”
	19	1	1	1	PWB	6456526	PWB

3-9

Image 27

Texas Instruments HPL-D SLLU064A manual 2. Bill of Materials for SN65LVDS125A / SN65LVDS250 EVM, EVM Construction

Contents

January SLLU064A4x4 Crosspoint Switch EVM Users GuideIMPORTANT NOTICE ProductsApplications EVM IMPORTANT NOTICE EVM WARNINGS AND RESTRICTIONS About This Manual How to Use This ManualRead This First PrefaceFCC Warning Figure 2-2. Termination for Interfacing LVDS, CML, or LVPECL Drivers ContentsFigures ContentsTables TablesChapter 1 Overview1 Overview 1.1 Sample Functional ConfigurationsSN65LVDS125A SN65LVDS250 4X4 Crosspoint Switch EVM Figure 1-2. 4x4 Crosspoint Switch EVMFigure 1-2 shows the 4x4 crosspoint switch EVM part number SN65LVDS125A or SN65LVDS250 installed and a copy of the data sheet1.2 Signal Paths Figure 1-3. 4x4 Crosspoint Switch Signal Paths1 Overview 2 Setup and Required Equipment 2.1 Applying an InputChapter SCOPE internally terminated 50 Ω to GND 2 Setup and Required EquipmentTable 2-1 Crosspoint Function Table Figure 2-2. Termination for Interfacing LVDS, CML, or LVPECL Drivers2 Setup and Required Equipment Note Power Supply 2.2 Observing an Output2.3 Typical Test Results 2 Setup and Required Equipment2 Setup and Required Equipment Figure 2-3. Typical Test Results2 Setup and Required Equipment 3 EVM Construction ChapterEVM Construction Figure 3-1. 4x4 Crosspoint Switch EVM Schematic 3.1 Schematic3 EVM Construction Figure 3-2. 4x4 Crosspoint Switch EVM Board Layout3.2 Board Layout Patterns 4X4 Crosspoint Switch EVMFigure 3-3. Layer 1-Signal Plane 3 EVM Construction Figure 3-4. GND Plane Figure 3-5. Layer 3-VccFigure 3-6. Layer 4-Vcc01 Plane Figure 3-7. Layer 5-GND Plane 3 EVM Construction Figure 3-8. Layer 6-GND/Signal Plane3.3 PCB Fabrication Requirements and Stack Up 3.4 Bill of Materials Table 3-2. Bill of Materials for SN65LVDS125A / SN65LVDS250 EVM3 EVM Construction