TOA Electronics NX-100, NX-100S 6-7

6-7

Chapter 6: APPENDIX

Remedy

Confirm that power is correctly connected.

Turn power on again.

Confirm that LAN cable is correctly connected.

Confirm that the NX-100/100S is connected to the correct switching

hub's port and that the proper type of cable is used for the connection.

→Refer to p. 2-3, Network Connections, for connections to other

networks.

Confirm that Java Runtime Environment is installed in PC using the

Setup/Operation programs.

→Refer to p. 2-9, Installing Java Runtime Environment, for correct

installation.

Check version number of installed Java Runtime Environment. Unit

may malfunction if version numbers differ.

→Refer to p. 2-9, Installing Java Runtime Environment, for

confirmation of the version number.

Confirm that PC using Setup/Operation programs is correctly

connected to network.

Confirm that unit's IP address, subnet mask, and default gateway are

correctly set.

→Refer to p. 3-8, Unit Scanning Tool, or p. 4-4, Network Setting, for

network setting procedures.

When connected to other networks via router, confirm with network

management personnel if the router is properly set.

If Java Runtime Environment is set to operate via a proxy server,

indications may not be properly displayed. Cancel the use of proxy.

(Perform this operation from the Control Panel.)

Check PC using Setup/Operation programs by way of browser for

correct connection. Also, confirm that browser is correctly set.

Setting screen uses Java Script. Confirm that browser is Java Script-

compatible and that the function is set to Enable.

Screen may not be properly displayed if browser is set to use a proxy

server. Do not use proxy server.

Check to see if correct type of cable is used.

Confirm that serial communication settings of both original and

connected units are correct.

→Refer to p. 3-27, Serial Bridge Setting, or p. 4-18, Serial Bridge

Setting, for serial communication setting.

Confirm that connections are correctly made to equipment that meets

unit's control I/O specification requirements.

3. IF A FAILURE IS DETECTED

Symptom

Cannot start up. No LEDs light.

LNK/ACT LED does not light.

Setup/Operation programs do not

start up.

Setup/Operation programs cannot

recognize NX-100 unit.

Browser setting screen is not

properly displayed.

Control inputs and outputs do not

operate.

Cannot carry out communications

using RS-232C interface.

NX-100 only

Contents

Main TABLE OF CONTENTS 6. SYSTEM SETTING TOOL 7. CHANGING THE SYSTEM NAME AND PASSWORD Page Page Page 1-2 1. GENERAL DESCRIPTION LAN / WAN 2. FEATURES 1 2 3 4 1-3 3. NOMENCLATURE AND FUNCTIONS 1 2 [Front] 5 6 7 8 1-4 [Rear] 19 21 17 1-5 1-6 4. SETTING TASK FLOWS (1) Unit Installation and Connection (2) Software Installation (4) Operation-Related Settings (3) System Setting Page 2-2 1. CONNECTIONS 1.1. Power Source Connections 2-3 1.2. Terminal Connections 2-4 2-5 2. CONNECTIONS TO TERMINAL PLUGS 2-6 3. RACK MOUNTING Use the optional MB-15B-J hardware set when mounting 2 units. 2-7 4. MAC ADDRESSES AND INSTALLATION LOCATIONS 2-8 5. SOFTWARE INSTALLATION 5.1. System Conditions 5.2. Activating the Setup Launcher 2-9 5.3. Installing Java Runtime Environment Page 2-11 5.4. Installing the NX-100 Software Page 2-13 2-14 2-15 5.5. Uninstalling Each Software Page 3-2 1. GENERAL DESCRIPTION 1.1. What is the NX-100 Setup Program? 1.2. About Network Settings 1.3. Backing-Up Setting Files 3-3 2. SETUP SOFTWARE CONFIGURATION AND SETTING ITEMS 3-4 3. SETTING PROCEDURE Pattern 1: Initial On-Site Setup (1) Unit Scanning (Network Setting) (2) System Setting 3-5 Pattern 2: Uploading the programmed system setting file after scanning the connected units on-site. (1) System Setting (2) Saving Data Files (3) Unit Scanning (Network Setting) 3-6 4. STARTUP OF INSTALLATION SETTING PROGRAM Page 3-8 5. UNIT SCANNING TOOL 5.1. Screen Description 3-9 5.2. Menu Important 3-10 5.3. Buttons (1) (2) 5.4. Scanning Units 3-11 5.5. Changing the Unit Setting Values 5.6. Automatic IP Address Assignment 3-12 5.7. Subnet Mask and Default Gateway Settings 3-13 6. SYSTEM SETTING TOOL 6.1. Screen Description 3-14 6.2. Menu 3-15 (1) (2) (3) (4) (5) (6) 3-16 6.3. Network Setting 3-17 3-18 6.4. Broadcast Spec Setting 3-19 Page 3-21 3-22 Page 3-24 3-25 3-26 3-27 6.7. Serial Bridge Setting NX-100 only 3-28 3-29 6.8. System Settings 6.9. Saving the Unit Setting Files 3-30 6.10. Reopening Unit Setting Files 6.11. Downloading the Operation Logs 6.12. Uploading Unit Setting Files 6.13. Downloading Unit Setting Files 3-31 7. CHANGING THE SYSTEM NAME AND PASSWORD Page 4-2 1. OUTLINE OF SETTING USING BROWSER 2. SETTINGS 4-3 4-4 3. NETWORK SETTING 4-5 4-6 4. BROADCAST SPEC SETTING 4-7 4-8 4-9 5. BROADCAST PATTERN SETTING 4-10 5.1. Pattern Selection Area 5.2. Pattern Edit Area 4-11 4-12 4-13 6. CONTACT SETTING 4-14 6.1. Contact Input Setting 4-15 4-16 6.2. Contact Output Setting 4-17 4-18 7. SERIAL BRIDGE SETTING NX-100 only 4-19 4-20 8. LOG MANAGEMENT 4-21 8.1. Operation Log 4-22 4-23 8.2. Saving Operation Logs 4-24 8.3. Stream Logs 4-25 4-26 8.4. Operation Status 4-27 9. SYSTEM MANAGEMENT 4-28 4-29 4-30 4-31 Page 5-2 1. NX-100 OPERATION PROGRAM SUMMARY 2. STARTUP AND INITIAL SCREEN 5-3 5-4 4. MENU Before performing the setting using the Operation program 5-5 5. SETTING PROCEDURES USING THE OPERATION PROGRAM (1) Add the unit to the system. (3) Set the Selection buttons. (4) Set the Group buttons. 5-6 6. UNIT SETTING ADDITION 5-7 5-8 7. EDITTING THE BUTTON LAYOUT 5-9 (1) (2) (3) 5-10 (1) (2) (3) 8. SETTING THE SELECTION BUTTON CONTENTS 5-11 Page 5-13 9. SETTING THE GROUP BUTTON CONTENTS (1) (2) (3) 5-14 5-15 10. ERROR MESSAGES Page 6-2 1. EXPLANATION 1.1. IP Network and Address 6-3 1.2. Network Address Translation (NAT) and Setup Software Programs 1.3. IP Broadcast and Unit Scan 6-4 1.4. Multicast and Simultaneous Multiple Broadcasts 1.5. Packet Loss Recovery 1.6. Contact OFF Delay Time 1.7. Sampling Frequency Correction 6-5 2. INDICATOR STATUS AND TROUBLESHOOTING 1 2 3 4 5 6 7 6-6 [Error indicator status] 1 2 3 4 5 6 7 6-7 3. IF A FAILURE IS DETECTED 6-8 6-9 4. SPECIFICATIONS 4.1. NX-100 6-10 4.2. NX-100S