TOA Electronics NX-100, NX-100S 3-17

3-17

Chapter 3: SYSTEM SETTINGS (NX-100 SETUP PROGRAM)

[Start port No.]

Enter the base number of the TCP port (other than web server, which is used by the unit). The default is

"5000." Enter the number from within the range of 1 – 65532.

The TCP ports are assigned as follows:

Port

Web server

Broadcast control

PC control

Contact bridge

Serial bridge

Port No.

Web server

Start port No. + 0

Start port No. + 1

Start port No. + 2

Start port No. + 3

Protocol

TCP

TCP

TCP

TCP

TCP

Default

80

5000

5001

5002

5003

(3) UDP port number assignment

Designate the base port number to be used by UDP.

[Start port No.]

Enter the base UDP port number to be used by the unit. The default is "5000." Enter an even number from

within the range of 1 – 65526.

The UDP ports are assigned as follows:

Port

Streaming

Error correction

Resend

Serial bridge

Fs* correction

Port No.

Start port No. + 0

Start port No. + 2

Start port No. + 4

Start port No. + 6

Start port No. + 7

Protocol

UDP

UDP

UDP

UDP

UDP

Default

5000

5002

5004

5006

5007

* Sampling frequency

Caution

Since UDP port No. 15000 is used by the unit, numbers between 14990 and 15000 cannot be used.

Contents

Main TABLE OF CONTENTS 6. SYSTEM SETTING TOOL 7. CHANGING THE SYSTEM NAME AND PASSWORD Page Page Page 1-2 1. GENERAL DESCRIPTION LAN / WAN 2. FEATURES 1 2 3 4 1-3 3. NOMENCLATURE AND FUNCTIONS 1 2 [Front] 5 6 7 8 1-4 [Rear] 19 21 17 1-5 1-6 4. SETTING TASK FLOWS (1) Unit Installation and Connection (2) Software Installation (4) Operation-Related Settings (3) System Setting Page 2-2 1. CONNECTIONS 1.1. Power Source Connections 2-3 1.2. Terminal Connections 2-4 2-5 2. CONNECTIONS TO TERMINAL PLUGS 2-6 3. RACK MOUNTING Use the optional MB-15B-J hardware set when mounting 2 units. 2-7 4. MAC ADDRESSES AND INSTALLATION LOCATIONS 2-8 5. SOFTWARE INSTALLATION 5.1. System Conditions 5.2. Activating the Setup Launcher 2-9 5.3. Installing Java Runtime Environment Page 2-11 5.4. Installing the NX-100 Software Page 2-13 2-14 2-15 5.5. Uninstalling Each Software Page 3-2 1. GENERAL DESCRIPTION 1.1. What is the NX-100 Setup Program? 1.2. About Network Settings 1.3. Backing-Up Setting Files 3-3 2. SETUP SOFTWARE CONFIGURATION AND SETTING ITEMS 3-4 3. SETTING PROCEDURE Pattern 1: Initial On-Site Setup (1) Unit Scanning (Network Setting) (2) System Setting 3-5 Pattern 2: Uploading the programmed system setting file after scanning the connected units on-site. (1) System Setting (2) Saving Data Files (3) Unit Scanning (Network Setting) 3-6 4. STARTUP OF INSTALLATION SETTING PROGRAM Page 3-8 5. UNIT SCANNING TOOL 5.1. Screen Description 3-9 5.2. Menu Important 3-10 5.3. Buttons (1) (2) 5.4. Scanning Units 3-11 5.5. Changing the Unit Setting Values 5.6. Automatic IP Address Assignment 3-12 5.7. Subnet Mask and Default Gateway Settings 3-13 6. SYSTEM SETTING TOOL 6.1. Screen Description 3-14 6.2. Menu 3-15 (1) (2) (3) (4) (5) (6) 3-16 6.3. Network Setting 3-17 3-18 6.4. Broadcast Spec Setting 3-19 Page 3-21 3-22 Page 3-24 3-25 3-26 3-27 6.7. Serial Bridge Setting NX-100 only 3-28 3-29 6.8. System Settings 6.9. Saving the Unit Setting Files 3-30 6.10. Reopening Unit Setting Files 6.11. Downloading the Operation Logs 6.12. Uploading Unit Setting Files 6.13. Downloading Unit Setting Files 3-31 7. CHANGING THE SYSTEM NAME AND PASSWORD Page 4-2 1. OUTLINE OF SETTING USING BROWSER 2. SETTINGS 4-3 4-4 3. NETWORK SETTING 4-5 4-6 4. BROADCAST SPEC SETTING 4-7 4-8 4-9 5. BROADCAST PATTERN SETTING 4-10 5.1. Pattern Selection Area 5.2. Pattern Edit Area 4-11 4-12 4-13 6. CONTACT SETTING 4-14 6.1. Contact Input Setting 4-15 4-16 6.2. Contact Output Setting 4-17 4-18 7. SERIAL BRIDGE SETTING NX-100 only 4-19 4-20 8. LOG MANAGEMENT 4-21 8.1. Operation Log 4-22 4-23 8.2. Saving Operation Logs 4-24 8.3. Stream Logs 4-25 4-26 8.4. Operation Status 4-27 9. SYSTEM MANAGEMENT 4-28 4-29 4-30 4-31 Page 5-2 1. NX-100 OPERATION PROGRAM SUMMARY 2. STARTUP AND INITIAL SCREEN 5-3 5-4 4. MENU Before performing the setting using the Operation program 5-5 5. SETTING PROCEDURES USING THE OPERATION PROGRAM (1) Add the unit to the system. (3) Set the Selection buttons. (4) Set the Group buttons. 5-6 6. UNIT SETTING ADDITION 5-7 5-8 7. EDITTING THE BUTTON LAYOUT 5-9 (1) (2) (3) 5-10 (1) (2) (3) 8. SETTING THE SELECTION BUTTON CONTENTS 5-11 Page 5-13 9. SETTING THE GROUP BUTTON CONTENTS (1) (2) (3) 5-14 5-15 10. ERROR MESSAGES Page 6-2 1. EXPLANATION 1.1. IP Network and Address 6-3 1.2. Network Address Translation (NAT) and Setup Software Programs 1.3. IP Broadcast and Unit Scan 6-4 1.4. Multicast and Simultaneous Multiple Broadcasts 1.5. Packet Loss Recovery 1.6. Contact OFF Delay Time 1.7. Sampling Frequency Correction 6-5 2. INDICATOR STATUS AND TROUBLESHOOTING 1 2 3 4 5 6 7 6-6 [Error indicator status] 1 2 3 4 5 6 7 6-7 3. IF A FAILURE IS DETECTED 6-8 6-9 4. SPECIFICATIONS 4.1. NX-100 6-10 4.2. NX-100S