TOA Electronics NX-100, NX-100S 4-2

4-2

Chapter 4: SYSTEM SETTINGS (SETTING USING BROWSER)

1. OUTLINE OF SETTING USING BROWSER

Settings can also be changed without requiring installation of the dedicated NX-100 software by individually

connecting to each NX-100/100S using the browser*.

For NX-100/100S units connected by way of the NAT function, such as an access via internet, perform

settings from the browser.

* Browsers that ensure correct NX-100/100S operation:

Microsoft Internet Explorer 6, Internet Explorer 5.5, and Netscape 7

Notes

• Settings cannot be performed if the network is not correctly set. In particular, new units shipped from the

factory may have duplicate default IP addresses or settings that assume the NX-100/100S is not connected

to the same network as the PC.

• Complete network settings before using the NX-100 Installation Setting program. If performing setup by the

browser, disconnect the unit from the network and connect it directly to the PC's LAN port using a cross

cable.

• Should the power be switched off during setting changes, the unit may be damaged.

• Changed settings are enabled after the NX-100/100S is restarted. Be sure to restart the unit whenever

settings are changed. Broadcasts are stopped during unit restart.

2. SETTINGS

Step 1. Start up the browser and enter the URL.

Note

The factory-preset IP address is "192.168.1.1" and web server port No. is "80." When the web server

port No. is "80," the description of the port number that follows the colon [:] can be omitted.

URL Example

http://<IP address>:<Web server port No.> /admin-e.htm http://192.168.1.1/admin-e.htm

The User Authentication dialog will be displayed. (Note that the dialog display may differ depending

on the browser used.)

Contents

Main TABLE OF CONTENTS 6. SYSTEM SETTING TOOL 7. CHANGING THE SYSTEM NAME AND PASSWORD Page Page Page 1-2 1. GENERAL DESCRIPTION LAN / WAN 2. FEATURES 1 2 3 4 1-3 3. NOMENCLATURE AND FUNCTIONS 1 2 [Front] 5 6 7 8 1-4 [Rear] 19 21 17 1-5 1-6 4. SETTING TASK FLOWS (1) Unit Installation and Connection (2) Software Installation (4) Operation-Related Settings (3) System Setting Page 2-2 1. CONNECTIONS 1.1. Power Source Connections 2-3 1.2. Terminal Connections 2-4 2-5 2. CONNECTIONS TO TERMINAL PLUGS 2-6 3. RACK MOUNTING Use the optional MB-15B-J hardware set when mounting 2 units. 2-7 4. MAC ADDRESSES AND INSTALLATION LOCATIONS 2-8 5. SOFTWARE INSTALLATION 5.1. System Conditions 5.2. Activating the Setup Launcher 2-9 5.3. Installing Java Runtime Environment Page 2-11 5.4. Installing the NX-100 Software Page 2-13 2-14 2-15 5.5. Uninstalling Each Software Page 3-2 1. GENERAL DESCRIPTION 1.1. What is the NX-100 Setup Program? 1.2. About Network Settings 1.3. Backing-Up Setting Files 3-3 2. SETUP SOFTWARE CONFIGURATION AND SETTING ITEMS 3-4 3. SETTING PROCEDURE Pattern 1: Initial On-Site Setup (1) Unit Scanning (Network Setting) (2) System Setting 3-5 Pattern 2: Uploading the programmed system setting file after scanning the connected units on-site. (1) System Setting (2) Saving Data Files (3) Unit Scanning (Network Setting) 3-6 4. STARTUP OF INSTALLATION SETTING PROGRAM Page 3-8 5. UNIT SCANNING TOOL 5.1. Screen Description 3-9 5.2. Menu Important 3-10 5.3. Buttons (1) (2) 5.4. Scanning Units 3-11 5.5. Changing the Unit Setting Values 5.6. Automatic IP Address Assignment 3-12 5.7. Subnet Mask and Default Gateway Settings 3-13 6. SYSTEM SETTING TOOL 6.1. Screen Description 3-14 6.2. Menu 3-15 (1) (2) (3) (4) (5) (6) 3-16 6.3. Network Setting 3-17 3-18 6.4. Broadcast Spec Setting 3-19 Page 3-21 3-22 Page 3-24 3-25 3-26 3-27 6.7. Serial Bridge Setting NX-100 only 3-28 3-29 6.8. System Settings 6.9. Saving the Unit Setting Files 3-30 6.10. Reopening Unit Setting Files 6.11. Downloading the Operation Logs 6.12. Uploading Unit Setting Files 6.13. Downloading Unit Setting Files 3-31 7. CHANGING THE SYSTEM NAME AND PASSWORD Page 4-2 1. OUTLINE OF SETTING USING BROWSER 2. SETTINGS 4-3 4-4 3. NETWORK SETTING 4-5 4-6 4. BROADCAST SPEC SETTING 4-7 4-8 4-9 5. BROADCAST PATTERN SETTING 4-10 5.1. Pattern Selection Area 5.2. Pattern Edit Area 4-11 4-12 4-13 6. CONTACT SETTING 4-14 6.1. Contact Input Setting 4-15 4-16 6.2. Contact Output Setting 4-17 4-18 7. SERIAL BRIDGE SETTING NX-100 only 4-19 4-20 8. LOG MANAGEMENT 4-21 8.1. Operation Log 4-22 4-23 8.2. Saving Operation Logs 4-24 8.3. Stream Logs 4-25 4-26 8.4. Operation Status 4-27 9. SYSTEM MANAGEMENT 4-28 4-29 4-30 4-31 Page 5-2 1. NX-100 OPERATION PROGRAM SUMMARY 2. STARTUP AND INITIAL SCREEN 5-3 5-4 4. MENU Before performing the setting using the Operation program 5-5 5. SETTING PROCEDURES USING THE OPERATION PROGRAM (1) Add the unit to the system. (3) Set the Selection buttons. (4) Set the Group buttons. 5-6 6. UNIT SETTING ADDITION 5-7 5-8 7. EDITTING THE BUTTON LAYOUT 5-9 (1) (2) (3) 5-10 (1) (2) (3) 8. SETTING THE SELECTION BUTTON CONTENTS 5-11 Page 5-13 9. SETTING THE GROUP BUTTON CONTENTS (1) (2) (3) 5-14 5-15 10. ERROR MESSAGES Page 6-2 1. EXPLANATION 1.1. IP Network and Address 6-3 1.2. Network Address Translation (NAT) and Setup Software Programs 1.3. IP Broadcast and Unit Scan 6-4 1.4. Multicast and Simultaneous Multiple Broadcasts 1.5. Packet Loss Recovery 1.6. Contact OFF Delay Time 1.7. Sampling Frequency Correction 6-5 2. INDICATOR STATUS AND TROUBLESHOOTING 1 2 3 4 5 6 7 6-6 [Error indicator status] 1 2 3 4 5 6 7 6-7 3. IF A FAILURE IS DETECTED 6-8 6-9 4. SPECIFICATIONS 4.1. NX-100 6-10 4.2. NX-100S