TOA Electronics VF5000-CMP-2 operating instructions Clearances, Check Gas Type, Preinstallation

To provide for the lowest possible shelf sur- face, combustible materials used to support a utility shelf directly above these appliances should be positioned just above the appliance top spacers. The minimum height from the base of the VF5000 to the underside of com- bustible materials used to construct a utility shelf is 34-1/2” (876 mm). The minimum height from the base of the VF6000 to the underside of combustible materials used to construct a utility shelf is 39-1/2” (1003 mm).

The appliance should be mounted on a fully supported base extending the full width and depth of the unit. The appliance may be located on or near conventional construction materi- als. However, if installed on combustible mate- rials, such as carpeting, vinyl tile, etc., a metal or wood barrier covering the entire bottom surface must be used.

If the appliance is to be elevated above floor level, a solid continuous platform must be constructed.

WARNING: MAINTAIN MINIMUM CLEARANCES.

Do not install in the vicinity of gasoline or other flammable liquids. The heater must be kept clear and free from these combustible materials and may not be located near where they are stored.

Clearances

WARNING: DO NOT INSTALL VF SE- RIES UNVENTED ROOM HEATERS IN SLEEPING QUARTERS, OR IN RECRE- ATIONAL VEHICLES.

Combustible
Finished Wall
Materials
12"
( mm)
	10''
26"	Header
	8''
( mm)
	Spacer
22-1/2"	6''
( mm)
18-5/8"
( mm)	2-1/2"
14-1/2"	( mm)
( mm)
8"	Top of Appliance
( mm)
	Top of Door Frame

VF Series

Figure 2

A hearth extension is not required with this appliance. If a hearth extension is used, do not block the lower control compartment door. Any hearth extensions used is for appearance only and does not have to conform to standard hearth extension installation requirements.

Note: Combustible wall finish materials and/or surround materials must not be allowed to encroach the area defined by the appliance front face (black sheet metal). Never allow combustible materials to be positioned in front of or overlapping the appliance front face.

6" Clearance to Combustible Side Wall

Max. Projection (See Fig. 2)

37-1/2" Min.

Remove wood slats and remove and discard the wood slat mount brackets. Loosen and remove the three (3) 1/4"-20 x 1" Phillips pan head screws at the three (3) tabs located along the door frame top edge. Tilt the glass door frame assembly outward and disengage the three (3) tabs along the bottom of the door from the three (3) brackets at the bottom of the firebox opening. Remove the door and set the panel aside protecting it from inadvertent dam- age. Retain the three (3) screws for use on reassembly. Remove the logs, packaged inside the firebox, and also set aside.

Check Gas Type

This appliance can only be connected to the gas type specified on the appliance data plate. This appliance can not be modified in the field for a different gas type. If the gas type to be used is not the one specified contact the dealer to obtain the correct gas appliance.

Note: Illustrations shown in this manual reflect “typical” installations with nominal dimensions and are for design and framing reference only. Actual installations may vary due to individual design preferences. However, always maintain minimum clearances to combustible materials and do not violate any specific installation re- quirements.

Note: The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence.

CAUTION: HEATERS CREATE WARM AIR CUR-

WARNING: DO NOT INSTALL THE VF UNVENTED ROOM HEATER:

Combustible Mantel

to Ceiling (953 mm)

RENTS. THESE CURRENTS MOVE HEAT TO WALL SURFACES NEXT TO HEATER. INSTALL- ING HEATER NEXT TO VINYL OR CLOTH WALL COVERINGS OR OPERATING HEATER WHERE

•WHERE CURTAINS, FURNITURE, CLOTHING OR OTHER FLAMMABLE OBJECTS ARE LESS THAN 42" FROM THE FRONT OF THE UNVENTED ROOM HEATER.

•IN HIGH TRAFFIC AREAS.

•IN WINDY OR DRAFTY AREAS.

Ensure the minimum clearances shown in Fig- ures 2 and 3 are maintained.

Minimum clearance to combustibles are:

Appliance:	side and back - 0"
	floor - 0"
	adjacent wall - 6"
	ceiling - 37-1/2” (953 mm)

(See Fig. 2)

Figure 3

PREINSTALLATION

Check that all listed parts have been received.

Carefully inspect the heater case and contents for shipping damage and immediately inform the dealer from whom you purchased the gas fireplace if any damage is found.

The appliance is shipped with all gas controls and components installed and pre-wired. Re- move the shipping carton, exposing the op- tional (if installed) front glass door frame.

NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE.

IMPURITIES IN THE AIR (SUCH AS TOBACCO SMOKE) EXISTS, MAY DISCOLOR WALLS.

Step 1. Position heater in desired location (freestanding, onto surround base or into pre- pared framing) and secure.

Step 2. Plumb gas line. (Gas connections should only be performed by an experienced, licensed/ certified tradesman.)

Step 3. Assemble logs and test flame appear- ance.

Step 4. Complete finish wall material, surround and optional hearth extension to your individual taste.

5