Toro LX500 manual Battery, Cutting Deck Removal, Jump Starting, Charging

Models: LX500

1 36
Download 36 pages 60.68 Kb
Page 26
Image 26

IMPORTANT:When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade spindle hex flange nut to between 70 lbs-ft. and 90 lbs- ft.

Battery

California Proposition 65 Warning: Battery

posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

Always keep the battery cables and terminals clean and free of corrosive build-up.

After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals

Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery, disconnect the NEGATIVE (Black) wire from its terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire to the POSITIVE (+) terminal before connecting the NEGATIVE (Black) wire to the NEGATIVE (-) terminal. Be certain that the wires are connected to the correct terminals; reversing them could change the polarity and cause damage to your engine’s alternator.

Jump Starting

WARNING: Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch.

Connect positive (+) cable to positive post (+) of your tractor’s discharged battery.

Connect the other end of the (+) cable to the positive (+) post of the jumper battery.

Connect the second negative (–) cable to the negative (–) post of the jumper battery.

Make the final connection on the engine block of the stalled tractor, away from the battery. Attach to a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle’s engine when jump starting your tractor.

Start the tractor (as instructed on page 16).

Set the tractor’s parking brake before removing the jumper cables, in reverse order of connection.

Allow the tractor’s engine to run for 15 minutes before shutting it off to allow the alternator time to charge the discharged battery.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive- type 12-volt charger for a minimum of one hour at a maximum of six amps.

WARNING: Batteries give off an explosive gas while charging. Charge battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

Place the PTO/Blade Engage knob in the disengaged (OFF) position and engage the parking brake.

Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

Remove the deck belt from around the tractor’s electric PTO clutch (refer to Changing the Deck Belt).

Looking at the cutting deck from the left side of the tractor, locate the deck support pin on the rear left side of the deck.

Rotate the pin slightly toward the rear of the tractor and release it.

Pull the deck support pin outward to release the deck from the deck lift arm. See Figure 19.

Support Pin

Figure 19

Repeat the above steps on the tractor’s right side.

Move the deck lift lever into the top notch to raise the deck lift arms up and out of the way.

26

Page 26
Image 26
Toro LX500 manual Battery, Cutting Deck Removal, Jump Starting, Charging

LX500 specifications

The Toro LX500 is a highly regarded riding lawn mower that combines power, comfort, and cutting-edge technology to deliver a premium lawn care experience. Designed for homeowners with medium to large yards, the LX500 stands out in the crowded market of garden equipment with its robust features and user-friendly design.

One of the main characteristics of the LX500 is its powerful engine. It typically comes equipped with a reliable 500cc engine, providing more than enough power for tackling tough mowing tasks. The engine is designed for durability, ensuring longevity and efficient performance. Its high output allows users to handle even overgrown grass with ease, making it a versatile option for various lawn conditions.

The cutting deck of the Toro LX500 offers a generous cutting width, often around 50 inches, which enables users to cover more ground in less time. The deck is crafted from high-quality materials, ensuring durability as well as superior cut quality. With multiple cutting height adjustments, users can customize the mower to achieve the desired grass length, enhancing their lawn’s appearance.

Comfort is a significant focus in the design of the LX500, as it features an ergonomic seat equipped with armrests and adjustable settings. This emphasis on user comfort allows for longer mowing sessions without fatigue. Additionally, it incorporates a smooth steering system, making maneuvering around obstacles and tight spaces less challenging.

The Toro LX500 also incorporates advanced technologies, such as the Smart Speed control system, allowing users to adjust the speed of the mower based on the task at hand. This feature ensures maximum efficiency whether mowing, towing, or handling other yard tasks. Furthermore, the mower is designed for easy maintenance, with accessible components for oil changes, filter replacements, and blade sharpening.

Another notable feature is the inclusion of a washout port for the mower deck, which simplifies the cleaning process and helps maintain performance. This ensures that grass clippings and debris don’t accumulate, leading to a clean cut every time.

Overall, the Toro LX500 represents a well-balanced combination of power, efficiency, and comfort, making it a worthy investment for anyone looking to maintain a beautiful lawn efficiently. With its robust features and user-focused design, it is poised to meet the demands of modern lawn care.