Evaporative Emission Control Warranty Statement

California Evaporative Emission Control Warranty Statement

Your Warranty Rights and Obligations

Introduction

The California Air Resources Board and The Toro® Company are pleased to explain the evaporative emission control system’s warranty on your 2006 model year equipment. In California, new equipment that use small off-road engines must be designed, built, and equipped to meet the State’s stringent anti-smog standards. The Toro® Company must warrant the evaporative emission control system on your equipment for two years provided there has been no abuse, neglect or improper maintenance of your equipment.

Your evaporative emission control system may include parts such as: fuel lines, fuel line fittings, and clamps.

Manufacturer’s Warranty Coverage:

This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be repaired or replaced by The Toro® Company.

Owner’s Warranty Responsibilities:

As the equipment owner, you are responsible for performance of the required maintenance listed in your Operator’s Manual. The Toro® Company recommends that you retain all receipts covering maintenance on your equipment, but The Toro® Company cannot deny warranty solely for the lack of receipts.

As the equipment owner, you should however be aware that The Toro® Company may deny you warranty coverage if your emission warranty parts have failed due to abuse, neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your equipment to an Authorized Service Dealer as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact The Toro® Company at 1-952–948–4027 or call us toll free at the number listed in your Toro Warranty statement.

Defects Warranty Requirements:

1.The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.

2.General Evaporative Emissions Warranty Coverage. The emission warranty parts must be warranted to the ultimate purchaser and any subsequent owner that the evaporative emission control system when installed was:

A.Designed, built, and equipped so as to conform with all applicable regulations; and

B.Free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.

3.The warranty on evaporative emissions-related parts will be interpreted as follows:

A.Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for the warranty period of two years. If any such part fails during the period of warranty coverage, it must be repaired or replaced by The Toro® Company. Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining warranty period.

B.Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty period of two years. A statement in such written instructions to the effect of “repair or replace as necessary” will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for a time not less than the remaining warranty period.

C.Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced by The Toro® Company. Any such part repaired or replaced under warranty must be warranted for a time not less than the remainder of the period prior to the first scheduled replacement point for the part.

D.Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at an Authorized Service Dealer.

E.Notwithstanding the provisions of subsection (D) above, warranty services or repairs must be provided at an Authorized Service Dealer.

F.The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at an Authorized Service Dealer.

G.Throughout the evaporative emission control system’s two year warranty period, The Toro® Company must maintain a supply of warranted parts sufficient to meet the expected demand for such parts.

H.Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the warranty obligations of The Toro® Company.

I.The use of any add-on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article. The Toro® Company will not be liable under this Article to warrant failures of warranted parts caused by the use of an add-on or modified part.

J.The Toro® Company shall provide any documents that describe the warranty procedures or policies within five working days of request by the Air Resources Board.

Emission Warranty Parts List:

The following lists includes the parts covered under this warranty:

Fuel Lines

Fuel Line Fittings

Clamps

35

374-0092 Rev A

Page 35
Image 35
Toro LX500 manual Evaporative Emission Control Warranty Statement, Introduction

LX500 specifications

The Toro LX500 is a highly regarded riding lawn mower that combines power, comfort, and cutting-edge technology to deliver a premium lawn care experience. Designed for homeowners with medium to large yards, the LX500 stands out in the crowded market of garden equipment with its robust features and user-friendly design.

One of the main characteristics of the LX500 is its powerful engine. It typically comes equipped with a reliable 500cc engine, providing more than enough power for tackling tough mowing tasks. The engine is designed for durability, ensuring longevity and efficient performance. Its high output allows users to handle even overgrown grass with ease, making it a versatile option for various lawn conditions.

The cutting deck of the Toro LX500 offers a generous cutting width, often around 50 inches, which enables users to cover more ground in less time. The deck is crafted from high-quality materials, ensuring durability as well as superior cut quality. With multiple cutting height adjustments, users can customize the mower to achieve the desired grass length, enhancing their lawn’s appearance.

Comfort is a significant focus in the design of the LX500, as it features an ergonomic seat equipped with armrests and adjustable settings. This emphasis on user comfort allows for longer mowing sessions without fatigue. Additionally, it incorporates a smooth steering system, making maneuvering around obstacles and tight spaces less challenging.

The Toro LX500 also incorporates advanced technologies, such as the Smart Speed control system, allowing users to adjust the speed of the mower based on the task at hand. This feature ensures maximum efficiency whether mowing, towing, or handling other yard tasks. Furthermore, the mower is designed for easy maintenance, with accessible components for oil changes, filter replacements, and blade sharpening.

Another notable feature is the inclusion of a washout port for the mower deck, which simplifies the cleaning process and helps maintain performance. This ensures that grass clippings and debris don’t accumulate, leading to a clean cut every time.

Overall, the Toro LX500 represents a well-balanced combination of power, efficiency, and comfort, making it a worthy investment for anyone looking to maintain a beautiful lawn efficiently. With its robust features and user-focused design, it is poised to meet the demands of modern lawn care.