Adding channels to the TV’s memory | Toshiba 27A60, 32A60, 36A60

To select the antenna input:

1.Press the TV/VIDEO button on the TV. The signal source you are connected to is displayed in purple.

TV

VIDEO 1 ANT 1

VIDEO 2 ANT 2

COLOR

STREAM

TO SELECT PUSH TV/VIDEO

TV/VIDEO

POWER

MENU TV/VIDEO VOLUME

CHANNEL

T S t s

Welcome to Toshiba

Connecting your TV

2.Press the button until ANT 1 or ANT 2 is displayed in purple, indicating the antenna terminal you wish to use.

Adding channels to the TV’s memory

Your TV will stop on specific channels that are stored in the TV’s channel memory when you press Channel ▲ or ▼. Use the steps below to set all active channels in your area automatically.

Programming channels automatically

Your TV can automatically detect all active channels and store them in its memory. After the TV has stored the channels in its memory, you can erase channels or add your favorite channels. If you use both ANT-1 and ANT-2 terminals, you must program channels for each input source.

To add channels:

1.Press MENU, then press x or • to highlight the SET UP menu.

2.Press y or z until the TV/CABLE selection is highlighted.

3.Press x or • to highlight either TV or CABLE, depending on which you use.

PICTURE AUDIO SET UP PREFER C.CAPT

LANGUAGE: [ENGLISH]FRANCAIS

ESPANOL

ANT1/2: [ANT1]ANT2

TV/CABLE: [TV]CABLE

CH PROGRAM

ADD/ERASE: [ADD]ERASE

MORE

SELECT[ ]

If you use an antenna, choose TV.

If you use cable, choose CABLE.

4.Press z to select CH PROGRAM.

5.Press x or • to start channel programming. The TV will automati- cally cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message “CH PROGRAM” appears.

6.When channel programming is complete, the message “CH Completed (channel or cable number)” appears.

7.Press Channel ▲ or ▼ to view the programmed channels.

RECALL MUTE POWER

1 2 3

4 5 6

7 8 9

CH RTN

100 0 ENT

CH

Menu/Enter

VOL MENU/ VOL

ENTER

CH

TV

CABLE

VCRExit

EXIT

Using the Remote Control

Setting up your TV

Using the TV’s Features

Appendix

Index

13

Image 19

Toshiba 27A60, 32A60, 36A60 owner manual Adding channels to the TV’s memory, Programming channels automatically

Contents

27A60 32A60 36A60 Instrucciones DE Seguridad Iii Service / Servicio DE Reparación Exploring your new TV Selecting a location for the TV Appendix 32A60 36A60 Welcome to ToshibaExploring your new TV Selecting a location for the TV Connecting a VCR Connecting your TV Connecting a cable converter box and a VCR Connecting a cable converter boxYou will need two coaxial cables Connecting a DVD with ColorStream and a VCR Connecting a DVD/satellite receiver and a VCR To Antenna Connecting two VCRs Connecting an audio amplifier Connecting a camcorder Using the remote control with a VCR or a cable TV converter Using the remote controlPreparing the remote control for use Installing the remote control batteries Recall Cable TV converter code table VCR code table NSC Location of Controls Remote ControlTV front panel Changing the on-screen display language Setting up your TVUsing the TV/VIDEO button When you are finished programming the menus, press Exit Programming channels automatically Adding channels to the TV’s memory Adding and erasing channels manually Changing channels Programming your favorite channels Using the TV’s featuresAdjusting the channel settings Switching between two channels Selecting a PIN code Using the V-ChipPress the x or to highlight Clear Blocking programs by ratings To change your PIN code General audience. Appropriate for all ages Parents strongly cautioned. Some material may beInappropriate for children under Appropriate for children Using the TV’s Features Appendix Index Blocking channels Blocking unrated movies or programs Code number. pag e16 Video LockPress x or to activate the menu. At the prompt, enter Section on V-Chip control on steps for entering the pin Press z to highlight Label Labeling channels Input source selected Video LabelPress x or . To exit the menu, press the Exit button PIP Watching picture-in-picture PIP Freezing the small picture Switching the main and small picturesWatching multi-window PIP Changing the position of the small picture Adjusting the picture quality Adjusting the picture Watching video input Setting the off-timerSelecting the color temperature Adjusting the picture preferences Press y or z to highlight C.CAPT Auto power offUsing the closed caption feature Press x or to select the closed caption mode Select T1, T2, T3, or T4 to view Text Adjusting the soundMuting the sound Selecting stereo/SAP broadcasts Press y or z to highlight MTS Press x or to highlight STR Adjusting the sound quality Understanding the last mode memory feature Viewing the demonstration modeUsing the surround sound feature Troubleshooting Cleaning and careAppendix Video 1 V p-p, 75 ohm, negative sync SpecificationsInput 0.286 V p-p burst signal, 75 ohm Input 1 V p-p, 75 ohm, negative sync Limited United States warranty Continental U.S If your TV requires service, call toll freeLimitations Index Adjusting Programming 23563915A Toshiba Hawaii, Inc