Toshiba 34AS41 14

Press T or S to adjust the selected function.

Set up

Preparation

Menu function (general instructions)

To adjust any TV feature, you must use the menu function. You can access the menus using the buttons on the TV or remote control.

The following are general instructions for using the menu system:

MENU

TV / VIDEO VOLUME

CHANNEL

1 Repeatedly press MENU to select a menu (Picture, Audio, Setup, or Option, as shown below).

POWER

Reference Section Advanced Operation Basic Operation

MENU

T/S t/s

	RECALL		MUTE			POWER
	RECALL		MUTE
	RECALL		o
	1		2			3
	4		5			6
	7		8			9
					CH RTN
	100		0			ENT
			CH
	T/S		MENU/				s/t
	VOL		MENU/		VOL
			ENTER

	MENU		CH
			CH
	TV
	CABLE						EXIT
	VCR		EXIT				EXIT
			FAV CH TV/VIDEO
						A
	REC	TV/VCR		STOP		PLAY
		STILL		SOURCE		PIP
	SLOW	PAUSE		REW		FF
	PIP CH			LOCATE		SWAP

2 Press t or s to select the function you want to adjust in the menu. The selected function will be displayed in purple.

3

4 The menus automatically disappear from the screen if no adjustments are made within 15 seconds. To clear an on-screen menu instantly, press EXIT on the remote control.

Picture 1

CONTRAST

–

+

BRIGHTNESS –

+

SHARPNESS

–

+

Picture 2

COLOR

–

+

TINT

RESET

MOVE[t s]

COLOR

TEMPERATURE:[COOL]MEDIUM WARM

PICTURE

Audio

PREFERENCE: [NORMAL]THEATER

MTS:

[STR]SAP MONO

MOVE[t s] SELECT[ BASS

–

+

TREBLE

–

+

Setup

BALANCE

–

+

SURROUND

TIMER:

0 MIN

MOVE[t s] SELECT[ TV/CABLE:

TV[CABLE]

CH PROGRAM

Option

ADD/ERASE:

[ADD]ERASE

V-CHIP CONTROL

FAVORITE CH

LANGUAGE:[ENGLISH]FRANCAIS

MOVE[t s]

ESPANOL

DEMO:

START[STOP]

C.CAPT:

C1 C2 C3 C4 T1

T2 T3 T4[OFF]

MOVE[t s] SELECT[T S]

Note:

The T/S buttons function as VOLUME T/S buttons when no menu is on-screen.

The s/t buttons function as CHANNEL s/t buttons when no menu is on-screen.

Model 34AS41 does not have PIP features.

14

Contents

Owner's Record CAUTION ATTENTION Note to CATV system installers in the USA Precautions Introduction Connecting your TV Preparing the remote control for use Location of controls on TV and remote control Using the remote control with a VCR or Exploring your new TV Selecting a location for your TV Audio and video cables are usually NOTE REGARDING PICTURE QUALITY When connecting video equipment, such as a VCR or DVD player: –For GOOD picture quality: Use regular video cables For BETTER picture quality: If your equipment has (continued) Connecting a cable converter box and a VCR Connecting a satellite receiver and a VCR Connecting a DVD player with component video and a VCR Connecting two VCRs •two pairs of audio cables (two single audio cables for mono VCRs) Section Installing the remote control batteries 1 Slide the battery cover off the back of the remote control 3 Slide the battery cover back onto the remote control until the lock snaps For details on the use of each control, refer to pages in brackets TV front panel Remote control ●The shaded buttons in the picture below glow in the dark ●Only the buttons used to operate the TV are described here Point the remote control at the VCR or cable TV converter Channel Number –If the correct code was entered, the VCR or converter will turn off If the correct code was entered –If the VCR or converter does not respond, repeat steps 1–4using another code If the VCR or converter does not respond to a different code VCR code table Cable TV converter code table Page Turning the TV set on Selecting the on-screendisplay language Understanding the Auto Power Off feature Understanding the Last Mode Memory feature TV/CABLE function CH PROGRAM function ADD/ERASE function 4 To add the channel: To erase the channel: Operation Basic Operation Selecting a TV channel Select a channel in one of the following two ways: ●Scan through the programmed channels in numerical sequence: –Press CHANNEL s to select the next higher channel RTN Adjusting the picture quality Pressing Selection To reset the Picture and Sound adjustments to the factory settings Selecting the color temperature The color temperature modes change the color tones of the picture 1 Press MENU until the Picture 2 menu is displayed on-screen 2 Press t or s until COLOR TEMPERATURE is displayed in purple 3 Press T or S until the desired mode is displayed in purple You can adjust the sound quality (BASS, TREBLE and BALANCE) to suit your taste Adjusting the sound quality 1 Press MENU until the Audio menu is POWERdisplayed on-screen 2 Press s or t until the item you want to Setting the off-timer Canceling the off-timer Stereo Sound: SAP: Surround Sound: Listening to stereo sound Activating the surround sound effect Listening to a second audio program (SAP) To deactivate the SAP feature: Programming your favorite channels Selecting your favorite channels Viewing captions or text Opening the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu (continued) Unblocking programs temporarily BLOCK CHANNEL function Page Page For additional information, visit our web site: ATTENTION CANADIAN CONSUMERS: Toshiba America Consumer Products, Inc Toshiba de Mexico, S.A. de C.V TOSHIBA AMERICA CONSUMER PRODUCTS, INC