Toshiba 34AS41 TV/CABLE function, CH PROGRAM function

Set up

Programming the channel memory

The channel memory is the list of TV channels your TV stops on when you press CHANNEL ▲/▼.

First, use the TV/CABLE and CH PROGRAM functions (below) to program all active channels in your area into the channel memory. Then use the ADD/ERASE function (page 17) to add/erase individual channels in the memory.

Preparation

CHANNEL t/s

TV/CABLE function

1 Press MENU until the Setup menu is displayed on-screen.

TIMER:	0 MIN
TV/CABLE:	[TV]CABLE

Basic Operation

MENU

TV / VIDEO VOLUME

CHANNEL

MENU T/S t/s

POWER

2 Press s or t until TV/CABLE is displayed in purple.

3 Press T or S until the mode that corresponds to your TV signal system displays in purple.

TV: TV broadcast signals

(VHF channels 2 through 13 and UHF channels 14 through 69)

CABLE: Cable TV signals

CH PROGRAM
ADD/ERASE:	[ADD]ERASE
V-CHIP CONTROL
FAVORITE CH
MOVE[t s] SELECT[T S]


TIMER:	0 MIN
TV/CABLE:	TV[CABLE]
CH PROGRAM
ADD/ERASE:	[ADD]ERASE

V-CHIP CONTROL

FAVORITE CH

MOVE[t s] SELECT[T S]

Operation

RECALL MUTE

o

POWER

(Cable channels 1 through 125)

Reference Section Advanced

T/S

1 2 3

4 5 6

7 8 9

CH RTN

100 0 ENT

CH

VOL MENU/ VOL

ENTER

Channel Number

s/t

CHANNEL

CH PROGRAM function

Use the CH PROGRAM function to automatically add all active channels to the channel memory.

1 Press MENU until the Setup menu is displayed on-screen.

2 Press s or t repeatedly until “CH PROGRAM” is displayed in purple.

TIMER:	0 MIN
TV/CABLE:	TV[CABLE]
CH PROGRAM
ADD/ERASE:	[ADD]ERASE

V-CHIP CONTROL

FAVORITE CH

MENUCH

TV

CABLE

VCR EXIT

FAV CH TV/VIDEO

A

REC TV/VCR STOP PLAY

STILL SOURCE PIP

SLOW PAUSE REW FF

PIP CH LOCATE SWAP

s/t

3 Press T or S to start channel programming. The TV automatically cycles through all the TV or CABLE channels (depending on the mode selected), and stores the active channels in the channel memory.

4 When channel programming is done, you will see the message, “Ch Programming Completed.”

5 Press CHANNEL s or t to scan through the programmed channels.

MOVE[t s] START[T S]

CH PROGRAM

CABLE 24

CH PROGRAMMING COMPLETED

CABLE 4

16

Contents

Owner's Record CAUTION ATTENTION Note to CATV system installers in the USA Precautions Introduction Connecting your TV Preparing the remote control for use Location of controls on TV and remote control Using the remote control with a VCR or Exploring your new TV Selecting a location for your TV Audio and video cables are usually NOTE REGARDING PICTURE QUALITY When connecting video equipment, such as a VCR or DVD player: –For GOOD picture quality: Use regular video cables For BETTER picture quality: If your equipment has (continued) Connecting a cable converter box and a VCR Connecting a satellite receiver and a VCR Connecting a DVD player with component video and a VCR Connecting two VCRs •two pairs of audio cables (two single audio cables for mono VCRs) Section Installing the remote control batteries 1 Slide the battery cover off the back of the remote control 3 Slide the battery cover back onto the remote control until the lock snaps For details on the use of each control, refer to pages in brackets TV front panel Remote control ●The shaded buttons in the picture below glow in the dark ●Only the buttons used to operate the TV are described here Point the remote control at the VCR or cable TV converter Channel Number –If the correct code was entered, the VCR or converter will turn off If the correct code was entered –If the VCR or converter does not respond, repeat steps 1–4using another code If the VCR or converter does not respond to a different code VCR code table Cable TV converter code table Page Turning the TV set on Selecting the on-screendisplay language Understanding the Auto Power Off feature Understanding the Last Mode Memory feature TV/CABLE function CH PROGRAM function ADD/ERASE function 4 To add the channel: To erase the channel: Operation Basic Operation Selecting a TV channel Select a channel in one of the following two ways: ●Scan through the programmed channels in numerical sequence: –Press CHANNEL s to select the next higher channel RTN Adjusting the picture quality Pressing Selection To reset the Picture and Sound adjustments to the factory settings Selecting the color temperature The color temperature modes change the color tones of the picture 1 Press MENU until the Picture 2 menu is displayed on-screen 2 Press t or s until COLOR TEMPERATURE is displayed in purple 3 Press T or S until the desired mode is displayed in purple You can adjust the sound quality (BASS, TREBLE and BALANCE) to suit your taste Adjusting the sound quality 1 Press MENU until the Audio menu is POWERdisplayed on-screen 2 Press s or t until the item you want to Setting the off-timer Canceling the off-timer Stereo Sound: SAP: Surround Sound: Listening to stereo sound Activating the surround sound effect Listening to a second audio program (SAP) To deactivate the SAP feature: Programming your favorite channels Selecting your favorite channels Viewing captions or text Opening the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu (continued) Unblocking programs temporarily BLOCK CHANNEL function Page Page For additional information, visit our web site: ATTENTION CANADIAN CONSUMERS: Toshiba America Consumer Products, Inc Toshiba de Mexico, S.A. de C.V TOSHIBA AMERICA CONSUMER PRODUCTS, INC