Manuals / Brands / TV and Video / Flat Panel Television / Toshiba / TV and Video / Flat Panel Television

Toshiba 34AS41 Programming your favorite channels, Selecting your favorite channels, “0.”, memory:, favorite channel, displayed on-screen, displayed in purple

1 35

Download 35 pages, 891.35 Kb

Set up

Using the favorite channel programming feature

The Favorite Channel Programming feature allows you to program up to 12 channels into the favorite channel memory. Once programmed, press the FAV CH t/s buttons on the remote control to scan through your favorite channels only, skipping other channels you do not normally view. You can still use the CHANNEL t/s buttons to scan through all the channels you programmed into the regular channel memory (see page 16).

Preparation

Basic Operation

MENU TV / VIDEO VOLUME CHANNEL		Programming your favorite channels
		1 Select a channel you want to program as a
	POWER	favorite channel.

MENU	T S t/s
	/

	2	Press MENU until the Setup menu is
		displayed on-screen.
	3	Press s or t until FAVORITE CH is
RECALL MUTE	POWER	displayed in purple.
RECALL MUTE

o

2

TIMER:	0 MIN
TV/CABLE:	[TV]CABLE
CH PROGRAM
ADD/ERASE:	[ADD]ERASE

V-CHIP CONTROL

FAVORITE CH

MOVE[t s] START[T S]

Advanced Operation

1 2 3

4 5 6

7 8 9

CH RTN

100 0 ENT

4 Press T or S to display the FAVORITE CH program menu.

FAVORITE CH
	[SET]CLEAR
0	0	0	0
0	0	0	0
0	0	0	0
[TV:CYAN,CABLE:BLUE]
SELECT[T S] SET[t s]

Section

T/S

CH

VOL MENU/ VOLs/t

ENTER

5 Press T or S to select SET. Then press

s or t until the channel number to be

MENU

CH

programmed (“2” in this example) replaces

“0.”

FAVORITE CH
	SET[CLEAR]
2	0	0	0

Reference

TV

CABLE

VCR EXIT

FAV CH TV/VIDEO

6 Repeat steps 1–5 for your other favorite

0	0	0	0
0	0	0	0

[TV:CYAN,CABLE:BLUE]

SELECT[T S] CLEAR[t s]

A

REC TV/VCR STOP PLAY

STILL SOURCE PIP

SLOW PAUSE REW FF

FAV CH

t/s

channels (for a maximum of 12 channels).

To clear channels from the favorite channel

PIP CH LOCATE SWAP

memory:

Select CLEAR in step 5 above. Then press s or t until “0” replaces the channel number to be erased.

Selecting your favorite channels

To select the favorite channels you have programmed, use the FAV CH t/s buttons on the remote control (instead of the CHANNEL s/t buttons).

Note: The FAV CH t/s buttons will not function until you have programmed your favorite channels.

26

Contents

Owner's Record CAUTION ATTENTION Note to CATV system installers in the USA Precautions Introduction Connecting your TV Preparing the remote control for use Location of controls on TV and remote control Using the remote control with a VCR or Exploring your new TV Selecting a location for your TV Audio and video cables are usually NOTE REGARDING PICTURE QUALITY When connecting video equipment, such as a VCR or DVD player: –For GOOD picture quality: Use regular video cables For BETTER picture quality: If your equipment has (continued) Connecting a cable converter box and a VCR Connecting a satellite receiver and a VCR Connecting a DVD player with component video and a VCR Connecting two VCRs •two pairs of audio cables (two single audio cables for mono VCRs) Section Installing the remote control batteries 1 Slide the battery cover off the back of the remote control 3 Slide the battery cover back onto the remote control until the lock snaps For details on the use of each control, refer to pages in brackets TV front panel Remote control ●The shaded buttons in the picture below glow in the dark ●Only the buttons used to operate the TV are described here Point the remote control at the VCR or cable TV converter Channel Number –If the correct code was entered, the VCR or converter will turn off If the correct code was entered –If the VCR or converter does not respond, repeat steps 1–4using another code If the VCR or converter does not respond to a different code VCR code table Cable TV converter code table Page Turning the TV set on Selecting the on-screendisplay language Understanding the Auto Power Off feature Understanding the Last Mode Memory feature TV/CABLE function CH PROGRAM function ADD/ERASE function 4 To add the channel: To erase the channel: Operation Basic Operation Selecting a TV channel Select a channel in one of the following two ways: ●Scan through the programmed channels in numerical sequence: –Press CHANNEL s to select the next higher channel RTN Adjusting the picture quality Pressing Selection To reset the Picture and Sound adjustments to the factory settings Selecting the color temperature The color temperature modes change the color tones of the picture 1 Press MENU until the Picture 2 menu is displayed on-screen 2 Press t or s until COLOR TEMPERATURE is displayed in purple 3 Press T or S until the desired mode is displayed in purple You can adjust the sound quality (BASS, TREBLE and BALANCE) to suit your taste Adjusting the sound quality 1 Press MENU until the Audio menu is POWERdisplayed on-screen 2 Press s or t until the item you want to Setting the off-timer Canceling the off-timer Stereo Sound: SAP: Surround Sound: Listening to stereo sound Activating the surround sound effect Listening to a second audio program (SAP) To deactivate the SAP feature: Programming your favorite channels Selecting your favorite channels Viewing captions or text Opening the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu (continued) Unblocking programs temporarily BLOCK CHANNEL function Page Page For additional information, visit our web site: ATTENTION CANADIAN CONSUMERS: Toshiba America Consumer Products, Inc Toshiba de Mexico, S.A. de C.V TOSHIBA AMERICA CONSUMER PRODUCTS, INC