8
(E) 46/52/62HM95
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
1. Carefully read the important safety, installation, care,
and service information on pages 2–5. Keep this
manual for future reference.
2. Observe the following when choosing a location for
the TV:
•
Place the TV on the floor or on the optional TV stand listed in
the “Specifications” section (page 106).
Overview of steps for installing, setting up, and using your new TV
Follow these steps to set up your TV and begin using its many exciting features.
Chapter 1: Introduction
• Place the TV in a location where light does not reflect on the
screen.
• Place the TV far enough from walls and other objects to allow
proper ventilation. Inadequate ventilation may cause
overheating, which will damage the TV. THIS TYPE OF
DAMAGE IS NOT COVER ED UNDER TH E TOSHIBA
WARRA NTY.
• Read “Installation” on pages 3–4.
• Read “Important notes about your DLP™ TV” on page 5.
3. Do not plug in any power cords until AFTER you have
connected all cables and devices to your TV.
4. BEFORE connecting cables or devices to the T V, learn
the functions of the TV’s connections and controls (pages 9
and 10).
5. Connect your other electronic device(s) to the TV
(pages 12–25).
6. Connect the G-LINK
®
cable (either one of the enclosed IR
blaster cables) from your VCR and/or Cable box (if applicable) to
the G-LINK
®
terminal so you can use the TV Guide On Screen
®
features (applies to VCRs and cable boxes only). See page 25.
7. Install the batteries in the remote control (page 28).
8. See “Learning about the remote control” (page 26) for
an overview of the buttons on the remote control.
9. Program the remote control to operate your other
device(s) (pages 28–34).
10. AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices.
11. After you plug in the TV power cord, the green LED
(on the TV front touchpad, to the left of the POWER button)
will blink while the TV is booting until the remote control is
usable. When the green LED stops blinking, press POWER to
turn on the TV.
See “LED indications” on page 99.
12. See “Menu layout and navigation” for a quick overview
of navigating the TV’s menu system (pages 35–36).
13. See Chapter 5 for details on setting up the TV Guide
On Screen
®
system (if available in your area).
14. See Chapter 7 for details on using the TV Guide
On Screen
®
program guide (if available in your area).
15. Program channels into the TV’s channel memory
(page 42).
16. Set up the TheaterNet™ on-screen device control
feature (if applicable to your particular home theater system
components) (page 45).
17. For details on using the memory card JPEG picture
viewer and MP3 audio player, see page 87.
18. For details on using the TV’s features, see Chapter 8.
19. For help, refer to the Troubleshooting Guide (Chapter
10).
20. For technical specifications and warranty information,
see Chapter 11.
21. Enjoy your new TV!
NOTICE OF POS SIBLE TV STAND IN STABILITY
DANGER: RISK OF SE RIOUS PERSONAL I NJURY
OR DEATH! Use this TV only with the TOSHIBA TV
stand listed in the “Specifications” section (page 106). Use with other
stands may result in instability, causing possible injury or death.
HM95_R1_007-08_061505 6/24/05, 8:46 PM8
IMPORTANT NOTICE ABOUT “HOT LAM P RESTART”
When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen
in the following situations:
•When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes.
•If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains
power within a few minutes.
This is a property of DLP TV lamp technology and is NOT a sign of malfunction.
If this occurs, the green LED on the TV front panel will blink (and the red LED will be lit solid) until the TV is finished restarting the lamp
and the normal picture appears. If BOTH green and red LEDs are blinking at a one-second rate, you will need to turn the TV off and then
on again to restart the lamp.