Getting started

Note:

After the Auto scan, the TV may have scanned identical channels being broadcast from different transmitters. You can verify this by previewing those channels in the Channel List with identical logical numbers and check on their physical channel numbers (- page 30). If you do find channels with the same logical channel numbers but different physical channel numbers, it is recommended that you skip these duplicate channels and keep only one channel with the best signal strength as indicated by the SNR indicator in the I-Plate (- page 16) display.

Manual scan - digital only -

If there were any missing channel after Auto Scan, these channels might be found by using Manual Scan described in this section. Also, if you do not live in Australia, you must use Manual Scan to scan those channels in your country.

1From the SCAN menu, press ￿ or ￿ to select Manual Scan, then press Q.

2Enter password using the Number buttons or press 0000 (which is the default password), then Manual Scan will appear.

Manual Scan

Programming channels automatically

- analog only -

First, use the Auto tuning function to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual tuning function so that you can tune into only desired channels.

1Press M, then press ￿ or ￿ to display the SET UP menu.

2Press ￿ or ￿ to select Auto tuning.

SET UP

 

 

 

 

 

 

Language

 

English

 

Auto tuning

OK

Manual tuning

OK

 

 

 

 

ANT ATT

 

Off

 

AV connection

OK

Picture position

OK

 

 

 

 

MENU Back EXIT Watch TV

 

 

3Press Q to display the Auto tuning menu.

Auto tuning

!Press OK key to start. EXIT for no c hange.

MENU Back EXIT Watch TV

4 Press Q to start the automatic search.

The search will begin for all available stations.

Channel No.

Frequency

Bandwidth

Priority

6

1775000 KHz

7MHz

HIGH

Scanning...

Auto tuning

Searching

Pos :2

EXIT Stop

Start Scan

Signal Level

100%

 

 

Quality70%

SNR: 20dB

The slide bar will move along the line as the search progresses.

If you make a mistake, simply repeat steps 1-4 to start again from the beginning.

Back Select Function

 

Watch TV

3Press ￿ or ￿ to select the item you wish to adjust. For Australia, to adjust Frequency, you may refer to the latest channel table from local dealer. And the

Bandwidth is 7MHz and Priority should be set to HIGH. Then press ￿ or ￿ to select Start Scan and press Q to start scanning.

4If scanning was successful, Get Channel Success appeared for 2 seconds. Repeat to scan other channels as necessary.

5If scanning was unsuccessful, Timeout Error appeared. At this point you can rescan the signal or refer to the Signal Level bar and Quality for aligning the direction of the antenna to get the signal. Refer to your antenna installer if problem persists.

Notes:

Signal level refers to the input Radio Frequency (RF) signal strength as perceived by the TV. Note that too strong signal may cause erroneous readings. If you use an antenna booster and find that you still get a low signal level, your booster gain may be set too high. In this case, adjust the gain accordingly. You may also see the No Signal on the screen when the signal level is low.

Quality refers to the quality of the received digital signal. A high value of quality means that there are few errors in the signal. In the same way, a low value of quality implies that there are a large number of errors in the signal, which may cause distortions in video and audio.

5When the automatic search is completed, the TV will automatically return to the first program position.

6Press ￿ or ￿ to view the programmed position.

Note:

When you preset the program channel which sound of broadcast transmission system adopts “M” system, the sound system may not be tuned correctly if the radio waves transmit badly. At that time, preset the channel by Manual tuning.

14

Page 14
Image 14
Toshiba 57X3000A owner manual Programming channels automatically, Press Q to display the Auto tuning menu