Toshiba 62HM195, 72HM195 Blocking channels, Unlocking programs temporarily, Locking video inputs

Chapter 9: Using the Locks menu

Blocking channels

With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you clear the setting first.

To block channels:

1.Press MENU and highlight the Locks menu icon.

2.Press z to display the

PIN code entering
screen.	Locks
	Enable Rating Blocking	Off
3. Enter your four-digit	Edit Rating Limits
	Channels Block
PIN code and press	Input Lock	Off
ENTER (see page 93 for	Front Panel Lock	Off
	Game Timer	Off
details).	New PIN Code
4. Press z to highlight	Navigate Select	CH RTN Back EXIT Exit
Channels Block and then press ENTER.

5.Using the yz x • buttons, select the input for which you want to change the rating limits (ANT 1, ANT 2, or Cable Box, if connected) and press ENTER.

A list of the channels available for that input will be displayed along with the call letters for each channel, if available.

Unlocking programs temporarily

If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. You can either unlock the program temporarily or select a non-locked program to watch.

To temporarily unlock the program:

1. Press MUTE.

2. Enter your four-digit PIN code and press ENTER. If the

correct code is entered,
	Locks							Active
the program lock mode	Enter PIN code to temporaily un-
is released and the
					block.
normal picture appears.
			*	*		*	*
All locking is disabled
until the TV is turned		Cancel					Done

off, and will be enabled

when the TV is turned on again.

Locking video inputs

6.Press yz to highlight the channel you want to block, then press

ENTER, which puts an “⋅” in the box next to that channel.

7.Repeat step 6 for other channels you want to block.

Channels Block

1

2

3

4

5

6

7

8

9

10

ANT 1

ANT 1

ANT 2

Cable Box

Allow All

Block All

Cancel

Done

You can use the Input Lock feature to lock the video input sources (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1, ColorStream HD-2, HDMI 1/HDMI 2) and channels 3 and 4. You will not be able to view the input sources or channels until you turn off the input lock.

To lock the video inputs:

1.	Press MENU and highlight the Locks menu icon.
2.	Press z to display the PIN code entering screen.

8. Highlight Done and press ENTER.

To unblock individual channels:

In step 6 above, press yz to highlight the channel you want to unblock, and then press ENTER to remove the ⋅ from the box, and highlight Done, and then press ENTER.

To block all channels at once:

Highlight Block All in step 6 above, and then highlight Done, and press ENTER.

3.	Enter your four-digit PIN code and press ENTER.
4.	Press z to highlight Input Lock and press •.
5.	Press y or z to select the level of video input locking you
	prefer, as described below:

Video: Locks VIDEO 1,
VIDEO 2, VIDEO 3,
ColorStream HD1/	Locks
	Enable Rating Blocking	Off	Off
HD2, and HDMI.	Edit Rating Limits		Video
	Channels Block		Video +
Video+: Locks VIDEO	Input Lock	Off
	Front Panel Lock	Off

To unblock all locked channels at once:

Highlight Allow All in step 6	Channels Block
above, and then highlight
		1

Done, and press ENTER.	2
	3
	4
	5
	6
	7
	8
	9
	10

ANT 1

ANT 1

ANT 2

Cable Box

Allow All

Block All

Cancel

Done

1, VIDEO 2, VIDEO 3,	Game Timer		Off
ColorStream HD1/	New PIN Code
HD2, HDMI 1/HDMI	Navigate	Select CH RTN Back EXIT Exit

2, and channels 3 and 4.

Select Video+ if you use the antenna terminal to play a video tape.

Note: Make sure the POP is not on channel 3 or 4.

Off: Unlocks all video input sources.

6. Press ENTER.

Note: Channel blocking may not take effect if you have a cable box connected and use the cable box controls to change channels.

Note: When a CableCARDª is inserted, Video+ will behave the same as Video lock.

		Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.	95
#01E_093-096_566272HM195	95	7/28/05, 5:02 PM
	Black

(E) 56/62/72HM195