Using the menu (Continued)
■The default setting menu
This menu shows placement status and other settings.
|
| Item |
|
| Description |
|
| |
|
|
|
| |||||
|
| Projection | Sets projection mode in accordance with Placement Style. p.20 | |||||
|
| mode | (Standard) | (Rear) | (Mounted |
| (Rear mounted | |
|
|
|
|
|
| from ceiling) |
| from ceiling) |
|
|
|
| |||||
|
| No signal | Set the timer to wait for the power to be turned off after signal input stops. | |||||
|
| power off | Press | . Switch with | and | . |
|
|
|
|
| Off (not turned off)/1 min./5 min./10 min./30 min./60 min. |
| ||||
|
|
|
|
| ||||
|
| Auto input | Set whether the input with signals is only selected or not. |
| ||||
|
| search |
|
|
|
| On | Off |
|
|
|
| |||||
|
| Power on | Sets whether to turn on the power when the ON/STANDBY button is pressed | |||||
|
|
| (Manual), or when the power cord is plugged in (Auto). Manual | Auto | ||||
|
| Lamp power [Note 1] | Sets the lamp power. |
| Low | Standard | ||
|
| Fan mode [Note 2] | Sets the cooling fan speed. | Standard | High | |||
|
| Reset all | Press | . |
|
| Yes | No |
|
|
|
| |||||
|
|
| Resets all adjustments and settings to their factory settings. | |||||
|
|
|
|
|
|
|
|
|
Notes
1:When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets quieter. The setting is cleared when you turn the power off.
2:Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level).
Notes
•Note that in the event of a power outage but the power is restored afterwards, the projector power will come on if Power on is set to Auto.
•When you turn off the projector even if Power on is set to Auto, you must press the ON/ STANDBY button to turn the power off.
■Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item | Description | Computer | Y/PB/PR | Video | PC | |
card | ||||||
|
|
|
| |||
Input | Input source name | Yes | Yes | Yes | Yes | |
Mode name | RGB input mode [Note 1] | Yes | No | No | No | |
Horizontal resolution (in dots) | Yes | No | No | No | ||
Vertical resolution (in dots) | Yes | No | No | No | ||
Horizontal sync frequency | Yes | No | No | No | ||
Vertical sync frequency [Note 2] | Yes | No | No | No | ||
Sync | Sync signal polarity [Note 3] | Yes | No | No | No | |
Signal format | Y/PB/PR signal format | No | Yes | No | No | |
Video mode | Color method of video signal | No | No | Yes | No | |
Lamp time | Time of lamp use [Note 4] | Yes | Yes | Yes | Yes | |
Lamp reset count | The count for lamp replacement | Yes | Yes | Yes | Yes | |
Total time | The total time that this projector is used | Yes | Yes | Yes | Yes | |
Version | Firmware version [Note 5] | Yes | Yes | Yes | Yes |
Notes
1:The mode of supported RGB signals p.69 is shown.
2:Same as the refresh rate of the computer signal.
3:Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult with a store about getting a TLPLV5 replacement lamp (sold separately) prepared.
5:[Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc.
Note
•The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again.
Operations
32 | 33 |
