1716

Preparations
(1)
(20) (18)(19) (17)
(9)
(10)(11)
(16)
(8) (7) (6)
(15) (13) (12)
(2)(3)(4)(5)
(14)
MONITOR
COMPUTER 2 IN
Y/P
B
/P
R
()
AUDIO OUT
AUDIO IN
CONTROL
S-VIDEO
VIDEO
COMPUTER 1 IN
Y/P
B
/P
R
()
R
L
Name :Main Function
(1) PC card slot : Insert PC cards here.
p.21
(2)
RESET switch (inside depression)
:Press if CARD indicator turns red.
p.21
(3) Eject button : Press to remove PC card.
p.21
(4) UNMOUNT button : Press before removing PC card.
p.21
(5) CARD indicator : Displays PC card’s status.
p.21
(6) Infrared remote sensor : Senses commands from the remote control.
p.18
(7) S-VIDEO terminal : Input S video signals from video equipment.
(8) AUDIO (L/R) terminal : Input audio signals from video equipment.
(9) CONTROL terminal : When operating the projector via a computer, connect
this to the controlling computer’s RS-232C port.
p.71
(
10
)AUDIO OUT terminal : Outputs audio signals.
(
11
)MONITOR terminal : Connect to a computer display, etc.
(
12
)AC IN socket : Connect the supplied power cord here.
(
13
)Main power switch :AC power line ON (standby)/OFF.
(
14
)Speaker : Outputs audio sound.
(
15
)Antitheft lock hole : Attach a safety cable or any other antitheft device.
(
16
)VIDEO terminal :Input video signals from video equipment.
(
17
)AUDIO (L/R) terminal : Input audio signals from video equipment.
(
18
)COMPUTER 1 terminal :
Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video equipment.
(
19
)AUDIO IN terminal :
Input audio signals from a computer or video equipment
with a component video signal output terminal.
(
20
)COMPUTER 2 terminal :
Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video equipment.
Note
•Although this owner’s manual abbreviates component video signals as Y/PB/PR, the
product also supports signals from video equipment marked “Y/CB/CR.”
Parts on the rear panelNames of each part on the control panel and remote control

Control panel Remote Control

(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9) (10) (11)
Name :Main Function
(1) ENTER button :Accepts the selected mode.
(2) MENU button : Displays menus.
p.29
(3) SET UP button : Sets up image and mode.
p.26
(4) ON/STANDBY button : Turns the power on/off (standby).
p.22
(5) ON indicator :Displays whether power is on or off.
p.22
(6) INPUT button : Selects input.
p.24
(7) RETURN button : Goes back one screen.
(8) Selection button : Menu selections and adjustments,etc.
p.30
(9) LAMP indicator : Displays lamp mode.
p.23
(
10
)TEMP indicator : Lights when internal temperature too high.
p.65
(
11
)FAN indicator : Displays cooling fan mode.
p.65
(
12
)FREEZE button : Pauses image.
p.28
(
13
)MUTE button : Cuts off the picture and sound temporarily.
p.28
(
14
)Numeric keypad :Use to set up the wireless LAN. Numbers and charac-
ters can be entered.
p.37
Note
•For the remainder of this manual, buttons are referred to as follows:
Selection buttons ⇒ ; ENTER button ⇒
Remote control
transmitter
(4)
(3)
(8)
(6)
(1)
(2)
(12)
(14)
(13)
(7)

■Removing the PC card

slot cover

Press on the circle (“O”) while
sliding the cover in the
direction of the arrow. The
cover will come off.
CAUTION
Do not carry the projector by having the PC card slot cover part.
Doing so may cause that cover to come off, resulting in the projector
malfunction, injury or damage.